iT For the circuit shown in figure beside, if the supply current is: i=5+10sin2000t+6cos4000t-4sin6000t mA. Write the current equations in each branch and then calculate the total power dissipated in the circuit. (Ans.: ic-8.9290° +7.462118.7°+4, IL 5+13.44-41.60+3.6-8 OMA & P₁=1747W) ww-H 100 $80 20μ F $8mH

iT For the circuit shown in figure beside, if the supply current is: i=5+10sin2000t+6cos4000t-4sin6000t mA. Write the current equations in each branch and then calculate the total power dissipated in the circuit. (Ans.: ic-8.9290° +7.462118.7°+4, IL 5+13.44-41.60+3.6-8 OMA & P₁=1747W) ww-H 100 $80 20μ F $8mH

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

write down the overview of grid code technical requirements for high power WECS
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
What is voltage stability? How is reactive power linked with the voltage stability in the power system? Write down the effect of ‘Load Tap Changer (LTC)’ on voltage stability and analyze very briefly using P-U (nose) curve.
What happens if a new pi equivalent circuit given the busbar admintas matrix and reactance and susceptance values given in the figure between busbars 1 and 3 in a 3 bus power system is connected.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
In the circuit in Figure 2, the capacitor andThe circuit of resistance is defined as a load circuit.a) Find the average power dissipated by the load circuit?b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Interpreting the results obtained?c) In the circuit in Figure 2, with a resistance of 80 ohms 23?A coil of is connected in series. In this case,calculating transformer ratio () to optimize power delivery to the load? Obtainedinterpreting the result?d) Calculate the distributed load complex power and reactive power in the newly learned circuit?
The problem is shown in the image below, v1 = 20 angle 15° volts, V2 = 10 angle -30° volts, V3 = -5 angle of 10° volts, and other components are shown in the image (units in Ω). When R3 is the load, calculate the replacement voltage (VTh), and the replacement current (IN)
Select the base voltages for one section and calculate the base voltages for the rest of the sections. Remember that the voltages given are line-line. Calculate the current and impedance for all sections of the System. Assume a base complex power of 100 MVA.
IDSS=8mA , VP =-4VTo help plot the DC load line VGS=VG-IDRSa)Determine the value of Vgs when ID=1mAb)Determine the value of Vgs when ID=2mAc)Determine the value of Vgs when ID=3mAd)Determine the value of Vgs when ID=4mAe)Attach a Plot of JFET Characteristic Curve as shown in Figuref)What is the approximate VGSQ?g)What is the approximate IDQ in mA?h)Determine source voltage VS.i)Calculate the drain voltage VD.j)Calculate the drain-to-source voltage VDS.
What are the input and output impedances for the circuit shown in the figure?
a) For the 2-Bus AC system given in Figure (a) find V1 (amplitude and angle). All the values are given in p.u. Note: Mind complex power concept! b) For the HVDC equivalent circuit given in Figure (b) calculate V2. All the values are given in p.u.
Please can someone help me to verify if the "Schedule of Loads" inputs here are correct? Assume its only 1-phase, and there is no given of p.f., and the country should be based on is Philippines. Upvote will be given for sure in the end. Thank you so much!