It indicates the range of water content over which a cohesive soil behaves plastically

Q: The azimuth of a line is 207*. The back azimuth of the same line is A. 63* B. 297* C. 27* D. 117...

A: Azimuth is Angular measurement in a spherical coordinate system. Back Azimuth is calculated by addin...

Q: A wide flange section has the following properties. A- 6645 mm2 by - 152.40 mm t- 10.80 mm d- 449.58...

A: Given properties of wide flange section are            area A=6645mm2                   bf=152.40mm ...

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section ...

A:

Q: If the 3-day BOD (BOD3) of a waste is 100 mg/L & the BOD decay constant, k is 0.345 per day, its ult...

A:

Q: Michael purchased a laptop in installment basis worth P25800 and he needs to pay P3200 per beginning...

A: Given data: Laptop worth = P25800 Installment worth = P3200 every quarter Interest rate i = 2% compo...

Q: From the figure shown, Material 1 (brown) is enclosed inside Material 2 (grey). If there would be a ...

A:

Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading ...

A:

Q: A cantilever beam, 80 mm wide by 280 mm high and 9 m long, carries a load that varies uniformly from...

A: We will find moment at 5 m from free end and use bending equation.

Q: C. Steel bar whose length of 1 + 0.DD m and a radius of 10+MM mm. is subjected to torque which produ...

A:

Q: urlin spacing 1.5m lope 15 degrees read Load- 2.5kPa ve Load- 2.5kPa Wind Load 1.0Pa Vindward coeffi...

A:

Q: Jse K = 1.0 and E = 29,000 ksi, Fy = 50 ksi. No need to check the W10x A = d = 9.7 9.73 tw = 0.29 bf...

A:

Q: A flat steel bar, 25 mm wide by 2 mm thick and 1.5 m long, is bent by couples applied at the ends so...

A:

Q: L000145rad. 0.000125ra 7. For the overhanging beam show alculate the deflection of the elastic e rig...

A:

Q: Draw the load and moment diagram given the shear diagram below. V (kN)| 3700 1700 r (m) -3100 -4000

A:

Q: Determine plasticity index if liquid limit is 40% and plastic limit is 30%

A: Introduction : Plasticity index is equal to difference between liquid limit and plastic limit . The ...

Q: The bending moment acting on the triangular cross section of a beam is M = 3.6 kN. m. Determine the ...

A:

Q: An 16.0 kN car is designed with a 345-cm wheelbase. The center of gravity is located 55 cm above the...

A:

Q: What would be the temperature at which the bar will have a compressive stress of 3 MPa given that at...

A: Elongation due to temperature change δT=Lα(ΔT)ΔT=T2-T1=T2-(-20)=T2+20  

Q: Two tension ropes are connected to a wall and subject to forces as shown by the diagram below. Deter...

A:

Q: 2. Figure 2 shows a 0.8 m wide of rectangular sluice gate is hinged at point A on the wall of a rese...

A:

Q: 2. Find the derivative of each of the following (a) y = 3x+ 4 (b) y = 5x- 2x +1 (c) y 1/(+4) (d) y =...

A:

Q: Two tension ropes are connected to a wall and subject to forces as shown by the diagram below. Deter...

A:

Q: What is the maximum moment in the beam below: 9 ft 9 ft 8 kips 2.1 kip/in a. 85 kip-ft b. 36 kip-ft ...

A:

Q: You have been asked to design the pavement for an access highway to a major truck terminal. The desi...

A:  Given - 

Q: W10x33 A = 9.71 d = 9.730 tw 0.290 %3D bf = 7.960 tf = 0.435 rx = 4.190 ry = 1.940

A:

Q: Given data : Lateral strain=-0.25 Longitudinal strain=D0.45 Determine Poisson's ratio

A: Using formula

Q: please draw normal, shear , and bending moment diagram for this (reactions are already calculated in...

A: The given diagram is shown below, To determine Draw the Shear force and bending moment diagram  

Q: Four equal wheel loads of 30 kN each, separated by 1 m between each load, roll as a unit across a 14...

A:

Q: A 31 mm diameter bronze bar 3.7 m long is placed between two rigid walls. At a temperature of -39°C,...

A:

Q: A water strikes to a vane with stationary velocity 25 m/s as shown in the Figure 3. It is given the ...

A:

Q: Determine the maximum moment in kN-m.

A: Structural analysis:  

Q: Given data : Mass=2 kg Velocity=3 m/s Determine kinetic energy

A: Introduction : The energy in body due to motion is called kinetic energy . For a body to have kineti...

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the t...

A:

Q: Figure 2 shows a 0.8 m wide of rectangular sluice gate is hinged at point A on the wall of a reservo...

A: We will first find centroid and calculate Force. By using formula of centre of pressure we will calc...

Q: The vertical reducing section shown in the figure contains oil with S flowing upward at the rate of ...

A:

Q: Prob. 1.4-19. A vertical force P = 10 kips acts downward at the apex B of frame ABC, as shown in Fig...

A:

Q: n, solve the absolute maximum shear stress.

A: CALCULATIONS OF ABSOLUTE MAXIMUM SHEAR STRESS###  

Q: A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carr...

A:

Q: Solve for the normal stresses at members CE, CH, and BC in MPa if the area of each truss member is 1...

A:

Q: A cantilever beam, 70 mm wide by 230 mm high and 8 m long, carries a load that varies uniformly from...

A: We will calculate moment at 4m from free end and use bending equation to find stress.

Q: A solid 0.66-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaf...

A:

Q: Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diam...

A:

Q: A. A wood with a dimension MM+50 mm and DD+100 mm with DD+100 mm side is positioned vertically. is s...

A: Given that, MM = 08 and DD = 26 dimension of wood,  width, b = MM+50 =08+50 = 58 mm depth, d = DD+10...

Q: 5. Determine the force in each member of the truss. State if the members are in tension or compressi...

A:

Q: Find the forces (kN) on the members of the given truss. Determine also the magnitudes of the support...

A:

Q: Perform a cantilever method to determine the force and moment of the three‐storey frame given below....

A:

Q: Use K = 1.0 and E = 29,000 ksi, Fy = 50 ksi. No need to check the local stability of the column. W10...

A:

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 11 MPa. An...

A:

Q: that is 3 feet long is carrying a torque of magnitude the bar has modulus of rigidity = 12x10 6, dia...

A:

Q: pls answer with solution choices: in kg/m3 490 8050 77000 7850

A:

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.