It is known that the equivalent impedance of R=5 kiloOhm, L=4 H and Zab in the circuit given below is pure real (the imaginary part is zero). What is the phasor expression ofiR+10 -VoRiş)=10cos(500t+30°) mAthe current flowing through the coil in this case?O a) 12.5-j21.65 mAO B) 21.65-j12.5 mAOC) -21.65+jl2.5 mAOD) 12.5+j21.65 mAO TO) -12.5+j21.65 mA

Answered: Image /qna-images/answer/d341fdde-4793-464c-aa1a-ffa23a535f8b.jpg

It is known that the equivalent impedance of R=5 kiloOhm, L=4 H and Zab in the circuit given below is pure real (the imaginary part is zero). What is the phasor expression of 10 L- R (t) i,0-10cos(500t+30°) mA the current flowing through the coil in this case? O a) 12.5-j21.65 mA OB) 21.65-j12.5 mA OC) -21.65+jl2.5 mA OD) 12.5+j21.65 mA O TO) -12.5+j21.65 mA

It is known that the equivalent impedance of R=5 kiloOhm, L=4 H and Zab in the circuit given below is pure real (the imaginary part is zero). What is the phasor expression of 10 L- R (t) i,0-10cos(500t+30°) mA the current flowing through the coil in this case? O a) 12.5-j21.65 mA OB) 21.65-j12.5 mA OC) -21.65+jl2.5 mA OD) 12.5+j21.65 mA O TO) -12.5+j21.65 mA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
Q10. If the impedance of a circuit = 20 – j10n, if a voltage source is connected across this impedance, which if the following statements is correct?
The total impedance Z, of a circuit containung an inductor with inductance L and resistance R in series is given by Z  R  j2fL where f  frequency . If Z  (50  j200)ohm and f = 50Hz. Find R and L
An industrial load of200KW has a powerfactor of 0.5 lagging. Agroup of synchronousmotors operating at apower factor of 0.8leading is installed andthe over-all power factorimproves to 0.75 lagging.Determine the KVArating of the synchronousmotors installed.Answer = 130.2354 KVA
A ower system is operating at 1000Mw, 132kV, 50Hz, with 0.8 p.f. laging in parallelwith another line at 750OMW, 132kV, 50Hz with 0.707 p.f. lagging. Both are interconnectedat the station and when the compensating device is on, the overall power factor isimproved to 0.9 lagging. Suggest suitable capacitors, shunt and series. Individual loadsand combined load are to improve power factor to 0.9 in all cases.
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
In the circuit below, find the value of the load impedance ZL, which must be connected to the output of the circuit for MAXIMUM POWER TRANSFER. If this load impedance you found is connected, what is the amplitude, phase angle and angular frequency values of the circuit that will pass through the circuit? AB=06, BA=60
If the normalized admittance visible at a distance d from the load impedance is 1 - j5, how many mho should the input admittance of the parallel side line that must be connected to the 50 ohm transmission line at position d be? (mho = 1/ohm)
A single phase, 50Hz transmission line connected between two buses having line resistance of 3Ω, inductive reactance of 0.2 Henry. Both the ends of transmission lines are connected with series capacitors of 400microfarads each for series compensation. Then series impedance of the line is a.(3-j31) Ω b.(3-j59.6) Ω c.(3+j31)Ω d.(3+j59.6) Ω 2- Fast decoupled algorithm is not as accurate as the exact Newton Raphson algorithm for Variable number of iteration Fixed number of iteration Variable time per iteration Fixed time per iteration
An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitanceand resistance should be connected in series with the coil if the power input to the latter is toremain unchanged and the overall power factor is to be unity (in resonance)? The circuit isenergized by a 120 volt, 60 cps source.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage Vr and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 ohms, Vcoil = 22.4 V, Vr = 20 V and V = 36V. Calculate Xl and Xc