ITEM COST acid core solder $2.49 solder paste $0.59 stop valve $2.85 90° elbow $0.43 -inch copper tubing $5.34 RVALUES FOR CERTAIN MATERIALS MATERIAL R VALUE Air space (34 inches) 0.97 Brick veneer 0.56 Fiberglass insulation (3 inches) 11.00 Wallboard (interior) 0.79 Wood siding and building paper 0.86

ITEM COST acid core solder $2.49 solder paste $0.59 stop valve $2.85 90° elbow $0.43 -inch copper tubing $5.34 RVALUES FOR CERTAIN MATERIALS MATERIAL R VALUE Air space (34 inches) 0.97 Brick veneer 0.56 Fiberglass insulation (3 inches) 11.00 Wallboard (interior) 0.79 Wood siding and building paper 0.86

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 33R: When estimating weld cost, what weld joint design factors should be considered?

See similar textbooks

Similar questions

What chemicals alloys are a. considered to be contaminants to the weld metal? b. used to increase tensile strength in the weld metal? c. used to increase corrosion resistance? d. used to reduce creep?
The welding parameters to be used to butt weld a metal alloy are being evaluated. In order to set up the welding machine, the melting factor for the metal (f2) has to be determined. The welding machine can deliver 4000 watts of power and the heat transfer factor for the welding process (f1) is 0.9. The final weld bead consists of 8 0% filler metal and 40% parent metal. The melting temperature of the filler metal and the parent metal is the same 2540 deg F. The cross-sectional area of the weld bead is 0.5 sq inches. The rate at which filler metal is added to the weld is 1 cu inch per min. Conversion factor 1 Btu = 1055 J and 0 deg F = 460 deg R Calculate the melting factor.
What is a cold solder joint? Identify its causes, its appearance, and the means of correction.
A U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U-groove is prepared using a milling cutter so the radius of the groove is 3.0 mm. During welding, the penetration of the weld causes an additional 1.5 mm of material to be melted. The final cross-sectional area of the weld can be approximated by a semicircle with a radius of 4.5 mm. The length of the weld is 200 mm. The melting factor of the setup is 0.57 and the heat transfer factor is 0.86. (a) What is the quantity of heat (in Joules) required to melt the volume of metal in this weld (filler metal plus base metal)? Assume the resulting top surface of the weld bead is flush with the top surface of the plates. (b) What is the required heat generated at the welding source?
Calculate the heat input during the arc welding process, if the voltage is 32 volts, current is 120 amperes, the length of the weld is 94mm and the time to complete the weld 33 secs. 1-Speed S= 2-Heat Input (Watts)=
Arc welding is an example of pressure welding. Select one: True False
9. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi i) what is the weld capacity of the shear connection in kips? (2 decimal places)
Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?
What solder alloy can retain its strength at elevated temperatures?
Which of the following is not a factor that strengthened soft solder joints? a. Solder composition b. Penetration of the solder into the pores of the base metal surface. c. Design of joints d. Type of metals being joined
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?
21) Silver is used as filler metal in soldering process. Select one: True False