Jayvee pulled a lever at a rate of 22.5 rad/s. Solve the following: a. At 10.3 s, what is the value of the angular position? b. If the lever of length 1.3 m is applied a force of 35.4 N, how much torque was applied? C. How much power was exerted given the torque in part b?

Jayvee pulled a lever at a rate of 22.5 rad/s. Solve the following: a. At 10.3 s, what is the value of the angular position? b. If the lever of length 1.3 m is applied a force of 35.4 N, how much torque was applied? C. How much power was exerted given the torque in part b?

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter10: Rotational Motion And Angular Momentum

Section: Chapter Questions

Problem 38PE: Suppose you start an antique car by exerting a force of 300 N on its crank for 0.250 s. What angular...

See similar textbooks

Related questions

Q: SOLVE STEP BY STEP IN DIGITAL FORMAT 1. Calculate the magnitude of the angular velocity of a truck…

Q: An Atwood's machine consists of blocks of masses m, - 12.0 kg and m, = 19.0 kg attached by a cord…

Q: A force (represented by FT→) is applied to a cord wrapped around a pulley (moment of inertia 0.385…

Q: A 3.00 kg rock has a horizontal velocity of magnitude 12.0 m/s when it is at point P in the figure…

A: Write the expression for magnitude of angular momentum.

Q: WHAT DO YOU THINK (CONTINUED)? QUICKCHECK2 A figure skater begins to spin in an angular speed w…

A: Since, there is no external torque acting on the figure skater, the angular momentum after and…

Q: The 540 g bar is rotating as shown in (Figure 1). What is the angular momentum of the bar about…

Q: What is the angular velocity of the Earth as it moves around the sun in radians? What is the Moment…

A: 1. The reason for this is simple - the angular velocity is defined as the angle subtended in a…

Q: A vertical rectangular object of uniform mass M=10kg has sides a=0.7m and b=2.5m. It is pivoted from…

A: Given data: The mass of block is M=10 kg. Sides of object are a=0.7 m and b=2.5 m. Applied force…

Q: An object rolls without slipping down a 1.99 m high incline. What is the moment of inertia of the…

Q: A 95 N force is applied to the end of a .5 meter long torque wrench which gives a rise to a torque…

A: Given: The length of the wrench is L=0.5 m, The applied force at the end of a 0.5 m wrench is F=95…

Q: In (Figure 1), what is the net torque about the axle? Express your answer using two significant…

A: Given: The radius of the axle is 4 cm. The first force acting on the axle is 30 N.…

Q: A 0.140-kg wooden rod is 1.20 m long and pivots at one end. It is held horizontally and then…

A: a) he expression for the torque is

Q: 150-gram ball connected to one end of a cord with a length of 30 cm. What is the moment of inertia…

Q: An 8.79cm diameter floppy disk rotates at its fastest at 470 rpm. Part A: Express the angular…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Tom and Jerry both push on the 2.90-m-diameter merry-go-round shown in (Figure 1). Tom pushes with a…

A: Solution:Taking counter-clockwise moment as positive we have:τ = τtom + τjerry =51 sin 60°-36 sin…

Q: QUESTION 2 F3 %r F2 30° P. 140° Fi Figure 2 Figure 2 shows a nut being loosen by a wrench. The…

Q: For items 7-13 choose the letter of the best answer. No need to give explanations. 7. A force of 17…

Q: Two employees are walking through a rotating door, as shown in the figure below. The woman on the…

A: The net force acting on an object is equal to the mass times acceleration of the object. If the net…

Q: For each situation shown in the figure, determine the signs of the net torque, the initial the…

A: For each situation shown in the figure, determine the signs of the net torque, the initial angular…

Q: The rope shown in Figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about…

A: Given data: Mass of cylinder, m=4.0 kg Moment of inertia, I=0.020 kg.m2 Force, F=20 N Radius, r=10…

Q: 1. What should be done to increase the generated torque on a bar, with one end fixed to a point,…

A: Consider the equation of torque:τ = r→×F→where, r is the length of moment…

Q: final angular velocity

Q: Reconsider the situation given below. If Luis pulls straight down on the end of a wrench that is in…

Q: A 3.80 kg rock has a horizontal velocity of magnitude 12.0 m/s when it is at point P in the figure…

Q: The diagrams show the application of six different forces to a wrench turning a bolt (blue hexagonal…

A: torque I→ = r→× F→ = rFsinθ here r= perpendiculardistance from point of…

Q: What is the formula for calculating the torque (from the force)? Using the formula, list 3 different…

A: The torque is used in rotational mechanics the same way force is used in linear mechanics.

Q: A grinding wheel 0.39 m in diameter rotates at 1900 грm. Calculate its angular velocity in rad/s.…

A: Radius (r) = 0.39/2 = 0.195m Angular velocity (w) = 1900rpm 1 RPM = 0.10472 rad/s

Q: A force of 50 N is applied at the end of a wrench handle that is 24 cm long. The force is applied in…

Q: Water drives a waterwheel (or turbine) of radius 3.0 m as shown in the figure (Figure 1). The water…

Q: III. Torque and angular acceleration The rigid bar shown at right is free to rotate about a fixed…

A: Torque Angular acceleration Thus, the rod rotates in the counter clockwise direction

Q: A bicycle wheel undergoes a rotational motion at a constant rate of 1.2 rev/s2. If the wheel starts…

A: Given Angular acceleration = 1.2 rev/s2 IIntial angular velocity = 0 rev/s We have to calculate (I)…

Q: After fixing a flat tire on a bicycle you give the wheel a spin. (a) Ifits initial angular speed was…

Q: It takes a good deal of effort to make homemade ice cream. (a) If the torque required toturn the…

A: (a) The torque (τ) required to turn the handle on the ice cream is 4.5 Nm. Consider the handle…

Q: The page feed roller of a computer printer grips each 11-inchlong sheet of paper and feeds it…

Q: What is the magnitude of the angular acceleration of the blades? ΑΣΦ ? a = rad/s? Submit Request…

A: According to rotational kinematics ω=ω0+αt ω=Final angular speed ω0=Initial angular speed α=angular…

Q: Consider a bar, of length 5.5 m, shown in the figure, being acted on by three forces. The magnitudes…

A: The free body diagram of the rod.

Q: A nut needs to be tightened with a wrench. Which force shown will apply the greatest torque to the…

A: Torque

Q: A grinding wheel 0.40 m in diameter rotates at 2200 rpm . a.) Calculate its angular velocity in…

Q: An 8.79cm diameter floppy disk rotates at its fastest at 470 rpm. Part A: Express the angular…

A: According to the Bartleby guidelines, when a question with multiple subparts is given, only the…

Q: What is the net torque on the bar shown in (Figure 1), about the axis indicated by the dot? Express…

A: Given F = 11 N Left side force = 8.0 N Mass of bar is not mentioned So we can take it zero We have…

Q: Find the magnitude of linear acceleration of block Bif there is no slipping between the cord and the…

A: Given the masses of blocks A and B be 4.50 kg and 2.00 kg, respectively, the moment of inertia of…

Q: Order the torques exerted on the bolts in the illustrated scenarios, from largest to smallest.…

Q: Solve the following problems and show your solutions. 1.Convert 300 rpm to rad/s 2. What is the…

A: Considering 1 revolution = 2 pi radians , and 1 min = 60 sec the desired results can be obtained.

Q: The 22-cm-diameter disk in the picture attached can rotate on an axle through its center. What is…

Question

7. Jayvee pulled a lever at a rate of 22.5 rad/s. Solve the following:
a. At 10.3 s, what is the value of the angular position?
b. If the lever of length 1.3 m is applied a force of 35.4 N, how much torque was applied?
C. How much power was exerted given the torque in part b?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Answer yes or no 10 (he following questions, (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
Suppose you start an antique car by exerting a force of 300 N on its crank for 0.250 s. What angular momentum is given to the engine if the handle of the crank is 0.300 m from the pivot and the force is exerted to create maximum torque the entire time?
A person stands a distance R from a doors hinges and pushes with a force F directed perpendicular to its surface. By what factor does the applied torque change if the persons position and force change to (a) 2R and 2F, (b) 2R and F, (c) R and F/2, (d) R/2 and F/2?
Tom and Jerry both push on the 3.00-m-diameter merry-go-round shown in (Figure 1). Tom pushes with a force of 50.0 N and Jerry pushes with a force of 33.0 N . What is the net torque on the merry-go-round? Express your answer to three significant figures and include the appropriate units. What is the net torque if Jerry reverses the direction that he pushes by 180∘ without changing the magnitude of his force? Express your answer to three significant figures and include the appropriate units.
A man with a weight of 580N is doing push-ups. Please draw a free body diagram to show the forces and place the pivot point where it needs to go and explain why. To calculate the torque, Flsinθ, explain why an angle is not necessary for this problem? What is the force on each foot?
Luis uses a 20-cm-long wrench to tighten a nut, turning it clockwise. The wrench handle is tilted 30° above the horizontal, and Luis pulls straight down on the end with a force of 100 N. How much torque does Luis exert on the nut?
Two muscles create tension simultaneously on opposite sides of a joint. Muscle X, attaching 4 cm from the axis of rotation at the joint, exerts 336 N of force. Muscle Y, attaching 3.8 cm from the joint axis, exerts 293 N of force. How much torque is created at the joint by each muscle? What is the net torque created at the joint? In which direction will motion at the joint occur?
A 100 N force exerted at the end of a 0.50 m long torque wrench supplies a torque of 20 N·m.What is the angle between the force and wrench arm directions?
9.) A wheel that is initially at rest has forces applied to it, as shown in (Figure 1), and it begins to rotationally accelerate. a.) Calculate the net torque about the axle of the wheel shown in (Figure 1). Assume that a friction torque of 0.60 m⋅N opposes the motion. Express your answer using two significant figures. TNET=______________ m⋅N
The answers are provided; please explain the purpose of each equation and why they were used Consider a bar of length 5.5 m, being acted on by three forces and constrained to rotate about its left end. The magnitudes of the first two forces are 19 N and 28 N and the first force is acting on the end of the bar at an angle of 43° What is the torque in newton-meters, due to F1 on this bar relative to the left end? Ans. = 78.87 Nm Equation used: τ1 = rFsinθ What is the torque in newton-meters, due to F2 on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. Ans. = 77 Nm Equation used: τ2 = F2 x (L / 2) What is the magnitude of the force F3, in newtons, if the force is a distance 0.85 m from the left end and the bar is not rotating? Ans. = 183.38 N Equation used: F = (τ1 + τ2) / d
The figure below shows forces acting at various points on a metal shaft. The angles ? = 48°, ? = 35°, ? = 21°. The length ℓ = 3.6 m. Find the net torque (in N · m) on the shaft about the following axes. An axis through O perpendicular to the page (magnitude and direction) An axis through C perpendicular to the page (magnitude and direction)
A 95 N force is applied to the end of a .5 meter long torque wrench which gives a rise to a torque of 15 N*m. What is the angle between the wrench and handle? What is the direction of the force?