Joseph Rivera Proportional Reasoning (Fractions and Decimals) Nov 11, 5:32:48 PM The table below lists the masses and volumes of several pieces of the same type of metal. There is a proportional relationship between the mass and the volume of the pieces of metal. Volume Mass (grams) (cubic centimeters) 10.6 33.39 10.9 34.335 11.8 37.17 Determine the mass, in grams, of a piece of metal that has a volume of 12.8 cubic centimeters. Round your answer to the nearest tenth of a gram.

Joseph Rivera Proportional Reasoning (Fractions and Decimals) Nov 11, 5:32:48 PM The table below lists the masses and volumes of several pieces of the same type of metal. There is a proportional relationship between the mass and the volume of the pieces of metal. Volume Mass (grams) (cubic centimeters) 10.6 33.39 10.9 34.335 11.8 37.17 Determine the mass, in grams, of a piece of metal that has a volume of 12.8 cubic centimeters. Round your answer to the nearest tenth of a gram.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 36P

See similar textbooks

Similar questions

subtract the decimal fractions 582.476 liters-488.827 liters
A block of wood 0.56 m x 0.56 m x “h” meters in dimension was thrown into a liquid with SG = 2.078. It floats with 0.29 m projecting above the water surface. The same block was thrown into a container of a liquid having a SG of 1.8 and it floats with 0.18 m. projecting above the liquid surface. Determine the value of 'h' in meters. Round off to two decimal places.
1)Coefficient of elasticity of a fluid E = 200000 t / m²Considering that for 1 Atmosphere (10 t / m²) pressure increase, the ratio of the decrease in the volume of this fluid to the initial volume iswhich one is given correctly?a) 0.00003b) 0.000004c) 0.00005d) 0.00006e) 0.00007 Please write clearly and clearly. thanks in advance
9. A gutter with trapezoidal cross section is to be made from a long sheet of tin that is4√108 inches wide by turning up √108 inches on each side. What is the depth of thegutter for the greatest carrying capacity? Give your answer in exact form(not decimalform). 10. At what rate is the vertex angle of a right circular cone changing when the radius is 3 ft andthe altitude is 4 ft if the altitude is increasing at 6 inches per min and the radius is constant?
1. What is the volume of cylinder in the metric and english system? 2. What is the amount error in the metric and english system? 3.. What is the perecnt error in the metric and english system?
For the objects shown below sketch the object in the space provided after rotating it about the axis by the indicated amount.
The kitchen of a house measures 13 feet by 14 feet. There are 8-foot ceilingsin the house. Find the volume in the room in cubic meters. Round to thenearer whole cubic meter.
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units specified after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 lb-in, 100 kN)
Explain in detail how you calculated to get 4.42 mpa
answer it in 3 decimal places with proper units
express each measurement in centimeters.1.75 meters
Fluid Mechanics. Reg.no : 5395 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.