k = k ky- 2k ky- 3k F X

Q: ng based on the degress scal from 0 to 72

A: 4 steps are present in the IC cycle. inlet compression power exhaust

Q: -bide and ste exponent of 0.

A:

Q: 15 ft – 15 ft 15 ft 5 kips 5 kips 9 kips |A J 8 ft K F I Bo E H.

A: Vertical force applied at pont D on the truss = 5kips Vertical force applied at pont G on the truss…

Q: dy = m y2 dx

A:

Q: Which of the following is true? A. csc(-θ)=cscθ B. tan(-θ)=tanθ C. sin(-θ)=sinθ D.cos(-θ)=cosθ

A: Option D is correct Cos (-θ) = Cos θ Where sin (-θ) = - sin θ Tan θ=sinθcosθ Therefore , Tan(- θ)= -…

Q: Determine the forces in members EF and GI of the truss shown.

A: Determine Reactions at B and J Take moment about B

Q: TRUE OR FALSE

A: This is false. According to Newton's relativity theory, the observer on the spaceship is measured a…

Q: Petermine the displacement W= 0-589 J F = 0-3 N

A: Given data : Force=F Work done=W   Required : Displacement

Q: 4) dx dy 3y = x2

A:

Q: Mercury has a uniform coefficient of expansion Select one: O True O False

A:

Q: Given b- Bm * 3m a 60 degrees R6m C 10 m Eind

A: Solution:Given,b=8mr=3m @ 60 degreesR=6mC=10m Scale(1m=1cm)

Q: Wind power increases if the velocity of air flow decreases. Select one: O True O False

A: Wind power is power developed due to the kinetic energy of the wind which is converted by the…

Q: (x - ay) dx + 2 (y-x) dy = 0

A: According to the question, (x-2y)dx+2(y-x)dy=0It can be represented as-Mdx+Ndy=0on…

Q: A func tion f is given. 1- cos x f(x) = Is f even, odd, or neither?

A: Given: The function is f(x) = (1-cos x)/x.   The condition for a function to be even and odd is…

Q: 1.5 kips 6 kips 1.5 kips 0.8 ft F B A D 0.8 ft G 1.2 ft 1.2 ft 1.2 ft 1.2 ft

A:

Q: Which of the following pressure is the highest? a. 25x10-4 Pascal b. 45 micro Pascal c. 0.03…

A:

Q: FA -X B FB Alpha = 34 degrees

A:

Q: a) Ax B.C b) A. (BxC)

A:

Q: 30.) What line below points in the direction [1 0-1] ? a) AD b) CH c) FB d) GE

A:

Q: Which of the following statement is FALSE? An example of a shear thickening fluid is blood. This…

A:

Q: value of h will be

A: Given: Figure shows a schematic diagram of simple watt governor mechanismwith spindle o1o2 rotating…

Q: 1- One millivolt is one millionth of a volt. (a) True (b) False

A:

Q: (A. - Aa) x 100 %CW = A. Initial Specimen Measurements (% hard is 21% CW) % CW Calculated A, W. to…

A: Ao=wo*to    =1.007*0.125=0.125875 Ao-Ad=0.125875-0.1258=0.000075

Q: ke angle is 0°. The minimum value of sh

A:

Q: What does this symbol mean: Ø0,1

A: It is required to explain what does given symbol represents

Q: y (x- 6y)dx - x (2x - gy) dy = 0; x =1 , y = 1

A:

Q: mm 40 mm 1.5m

A:

Q: В 125 mm A 175 mm C OD - 225 mm 150 N 75 mm

A:

Q: normal sti D C 4 mm 6 mm

A: GivenAD=20mmAB=20mm

Q: FGQ=FGC=D0 Yes O No

A: For any truss members If 3 members are joint at any point and 2 of them are co-linear then third…

Q: Mark True or False 12- When OLX equals zero, it represents Newton's first law. true Error

A:

Q: - where p' = Ap. %3D

A: Answer- Option a)

Q: n or equal to u*N

A: The value of dynamic friction is less than the static friction. So force required in dynamic…

Q: °C. What is the distance of zero and 30 mark under these conditions?

A:

Q: In Problems 1-18 use Definition 7.1.1 to find L{f(t)}. f(t) = e' cos t

A:

Q: Which of the above mentioned values are correct for the value of n?

A:

Q: Change following into SI units (MKS): (c) 2 hours

A: Change following into SI units (MKS):   (c) 2 hours

Q: What line is K? A

A: What is line k

Q: V a A В a

A: a=2.3inb=3.6ind=10.8int=0.4inV=39kips To-Find:- The shear flow through the welded surface at B

Q: False

A: A non flowing fluid does not have flow energy so this component will not considered in total energy.…

Q: / solve: ☺ log (x)+Log (X-1) = log (8x-12)-1a9L2) Ans/ x= 2,3 %3D O 2. kucx) = hu (3)+ln c6-x) An…

A:

Q: haft G-Codes programming process (sumerik)

A: CNC programmers increasingly face special tasks that take them to the limits of classic (DIN 66025)…

Q: 120 mm 600 mm 10-N 4N 600 mm 4N

A:

Q: 4 kips/ft 1B 5 ft- 2 ft 2 ft 8 kins 8 kins

A: The loading diagram of the beam is shown as follows, Let's draw the free body diagram of the beam,

Q: D C 2 mm 5 mm

A: GivenAD=15mmAB=15mm

Q: Measured values The given system has precision. True value

A: Precision: The classness between the measured value and true value is known as precision.

Q: 2.x {x: (x- 2)(x+1) - 20}

A:

Q: x=-2-5-6/2m

A: Given   The relation is given      x=-2-5-62 Find   The value of x

Q: 5. [vZ (cos + i sin) ( 6. 3-2i

A:

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.