Answered: L= 1m, d = 2 mm Н Water at 20° C

Engineering

Mechanical Engineering

L= 1m, d = 2 mm Н Water at 20° C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: Q4:- Fully developed laminar flow between parallel plates with no pressure gradient as shown in…

Q: 1. A research experiment requires a laminar flow of water at 20°C through a 120mm diameter pipe at a…

Q: Water flows from a faucet into a sink at 3 U.S. gallonsper minute. The stopper is closed, and the…

A: As it is mention that the water level remains constant, water entering the system is equal to the…

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuil oil with S=…

Q: 3 Water with a viscosity of p=0.02 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30…

A: Given : - viscosity , μ = 0.02 kg/m .s density , ρ = 1000 kg/m3…

Q: 1 Water (u 0.001 kg/m.s) is siphoned from a large tank and discharges into the atmosphere through a…

Q: Gasoline at 20°C flows at 0.06 m3/s through a 15-cm pipeand is metered by a 9-cm long-radius flow…

A: Given data: The discharge of the gasoline is Q=0.06 m3/s For gasoline at 20 degrees: The density of…

Q: Consider inviscid flow past a sphere, as in Fig. Find(a) the point on the front surface where the…

Q: In Fig. , free discharge, a gate opening of 0.72 ft willallow a fl ow rate of 30,000 gal/min. Recall…

A: Given dataflow rate Q=30 000 gal/min width b=8 ft y1=6 ft y2=4 ft H=0.72 ft

Q: The Kishwaukee river has a volume flow rate of 21 ft3/sec with a depth of 2.8 ft. If the…

Q: Water (density 1000 kg/m', viscosity 1 mNs/m) is pumped through a 50 mm diameter pipeline at 4 kg/s…

A: We are suppose to solve only one question. Please post other question as a separate question. As per…

Q: The connecting pipe is commercial steel 6 cm in diameter. Estimate the flow rate, in m³/s, if the…

Q: Q4:- Fully developed laminar flow between parallel plates with no pressure gradient as shown in…

A: we have, Navier stokes equation for a fully developedlaminar flow given below.…

Q: C- Estimate the velocity at point (2) and discharge of oil that as a petroleum engineer want to…

A: From the data given, Change in pressure between section 1 and 2 = P1 - P2 = 100 kPa = 100 x 103 Pa…

Q: GLYCERIN (SP.GR. = 1.26 AND ABSOLUTE VISCOSITY OF 1.49 ?? − ? ) FLOWS THROUGH A RECTANGULAR CONDUIT…

Q: C- Estimate the velocity at point (2) and discharge of oil that as a petroleum engineer want to…

A: Given, Change in pressure between section 1 and 2 = P1 - P2 = 100 kPa = 100 x 103 Pa Diameter at…

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

Q: A fluid is flowing through a small diameter pipe of radius R1 and length L1. It then expands rapidly…

Q: Water with a viscosity of p=0.031 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30…

A: GIVEN :- viscocity of water : μ=0.031kg/m.sdiameter of tube : D=1.5 mmdensity of water :…

Q: For flow of water at 20°C through a straight, smooth pipe at0.06 m3/h, the pipe diameter for which…

A: Provided the water have the temperature of 20 deg Celsius and have a volumetric flow rate or…

Q: A pump delivers 1 hp to a water at 68°F flowing in a 10-in-diameter horizontal, cast iron pipe at V…

Q: UsingFig. P6.27. All parameters are constant except the uppertank depth Z(t). Find an expression for…

A: Energy: hf=32μLVρgd2=h+Z Mass balance:…

Q: Q2) For laminar flow conditions. Calculate the pipe diameter should be installed to carry 0.022m/s…

A: Given, Flow rate , Q = 0.022 m3/s Kinematic viscosity of oil , v = 0.00021m2/s Specific gravity =…

Q: A fluid is flowing through a small diameter pipe of radius R1 and length L1. It then expands rapidly…

A: Given data : For smaller diameter pipe, Radius R1, Length L1 For larger pipe diameter, R2=1.5R1…

Q: Incompressible steady flow in the inlet between parallel plates is uniform, Vo = 8 cm/s, while…

Q: estimate the distance X required to obtain a volume flow rate of 7.1 x 10^-3 m^3/s.

A: Given: The flow through pipe, Q = 7.1x10-3 m3/s The diameter of pipe, D = 50 mm = 0.05 m The…

Q: Laminar oil (u 0.1kg SG = 0.9) flows through a long, straight smooth 5 cm m.s diameter pipe at 14…

Q: strength can be combined with a uniform flow. The streamfunction potential is given by 2ay ý = Uy –…

A: Given that, The flow around a Rankine oval and a source and a sink of equal strength can be combined…

Q: estimate the allowable distance Y if the allowable pressure in the systems is -188kPa (gage). aasume…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Gasoline (s = 0.68, μ = 0.00029 kg/m.s) is being siphoned through a 18 mm, diameter plastic tube, as…

A: Given; Calculate the cross-sectional area of the pipe. Here, D is the diameter of the pipe.…

Q: 5.73 Assume the liquid film in Example 5.9 is horizontal (i.e., 0 = 0°) and that the flow is driven…

Q: Water with a viscosity of u=0.01 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30 m…

A: This question is solved with the help of Bernoulli's equation, Bernoulli's equation is based on the…

Q: A 10-cm-diameter smooth pipe contains an orifice platewith D: 1/2D taps and β = 0.5. The measured…

A: Given data: The diameter of the smooth pipe is D = 10 cm. The ratio of orifice diameter to the pipe…

Q: A surge chamber 10m in diameter is situated at the down stream end of a low pressure tunnel 9.8km…

Q: Oil, with p-950 kg/m' and v=2x10* m/s ,flows through a 30-cm-diameter pipe 100 m long with a head…

Q: Fluid flows steadily, at volume rate Q, through a large horizontalpipe and then divides into two…

A: Given data: The inside diameter of the large pipe is dL = 25 mm.

Q: Q4. There is a pipe flow of diameter (D) 0.60 meters and length with having (fluid- water) Discharge…

A: The head loss basically is the estimation of the amount of energy spent by the liquid to overcome…

Q: SAE 50W oil at 20 °C flows from one tank to anotherthrough a tube 160 cm long and 5 cm in diameter.…

A: Given: Length of the tube, L=160 cmL=1.6m Diameter of the tube, D=5cm Elevation of the tank 1,…

Q: Ethylene glycol at 20°C flows through 80 m of cast ironpipe of diameter 6 cm. The measured pressure…

A: Given dataLength of cast iron pipe L =80mDiameter of the pipe d= 6 cm = 0.06mPressure drop ∆p=…

Q: A smooth pipe (30 cm) diameter and (100m) long has flush entrance and submerged discharge. The…

A: Given Velocity, v = 3 m/s Diameter, D = 30 cm Length, L =…

Q: A heat exchanger consists of a series of passages between parallel plates. The pressure drop is…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Water at 20 ° C is to be siphoned through a tube 1 m long
and 2 mm in diameter, as in Fig. . Is there any height
H for which the flow might not be laminar? What is the
flow rate if H = 50 cm? Neglect the tube curvature.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the figure shown, stop B will break in the force on it reaches 40 kN. Find the critical water depth (h-bar) the length of the gate perpendicular to the sketch is 1.5m. Ans (5.77m)
A glass capillary tube is 0.2 mm in diameter. The surface tension is 0.0735 N/m. The pressure in the capillary water just under the meniscus will be ________ kN/m ^2.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation for the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover (D = 4 m). Find the magnitude of the applied force (Fa) as shown.
Water at 25° is flowing between A and B through a steel pipe 30 centimeters in diameter and a lengthof 47m. Point B is 10 meters above A and thepressure at B must be maintained at 1.4 kg/cm2. If 220 It/s circulate through the pipe, what pressure must exist in A?
What is the rise of water in glass capillary tube having radius 0.5 mm and surface tension as 0.1 N/m^2 Assume contact angle of water and glass is 0 degree
Find the capillary raise of the water in the tube of diameter 6mm, which is immersed vertically in the container. The surface tension of water is 0.07115 N/m. Take the angle of contact is = 00 The capillary raise of water in the tube is (unit in mm)= ______
Answer is: V = 14.17 ft/s
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
What is the minimum diameter at section (1) to avoid cavitation at that point? Take D2 = 15 cm.
Note: Please state what formula you are using. And please be clear and detailed with your solution. Atleast explain. It will help me, thanks. Problem: A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45o from the vertical with vertex pointing upward. The base of the gate is 2.70 m below the surface of oil (s = 0.80). What normal force must be applied at the vertex of the gate to open it? Show figure
The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover is D = 4 m. Find the magnitude of the applied force (Fa) as shown. Take the density of water as 999kg / m3.
Water is the fluid in the pipe as shown, and mercury is the manometer fluid. If the deflection Δh is 60 cm and L is 180 cm, what is the gage pressure at the center of the pipe in kPa? delta h is between point 1 and 2.