L A spiral column having a diameter of 448 mm carries a dead load of 1,107 KN including self-weight and a live load of 995 KN. If fc' = 27.5 MPa, fy = 413.5 MPa. Consider minimum possible longitudinal reinforcement, determine the spacing of the 10mm dia. spirals. Assume concrete cover of 40mm. Answer in two decimal places in mm.

L A spiral column having a diameter of 448 mm carries a dead load of 1,107 KN including self-weight and a live load of 995 KN. If fc' = 27.5 MPa, fy = 413.5 MPa. Consider minimum possible longitudinal reinforcement, determine the spacing of the 10mm dia. spirals. Assume concrete cover of 40mm. Answer in two decimal places in mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design Slab DEGH of the floor system shown below. Dead load pressure including the slab's weight is estimated at 5.3 kPa while live load pressure is 2.4 kPa. Use fc' = 21 MPa and fy = 345 MPa. The supporting beam is 350 mm x 500 mm. Use 12mm diameter bars. 6m A B 6m C 2.6 m D 2.6 m 2.6 m J E H K LL F I L
A rectangular beam 250mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80mm and at the bottom is 70mm. Use concrete strength f’c=21 MPa and steel yield strength fy=415MPa for 20-mm bars and fy=275MPa for 16mm bars. Determine the limiting tensile stress ratio for a tension controlled condition in positive or negative bending with the given material strengths.
38 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in positive bending. Write the answer in 2 decimal places only.
A corner column is reinforced with 12 - 20mm dia. RSB with fy = 415 MPa. Concrete Strength f'c = 28 MPa. Neglect the concrete area occupied by longitudinal reinforcement A. Locate the plastic centroid measured from x-axis and y-axis B. Resultant factored moment due to a factored axial load Pu = 3000 kN applied at 300 mm normal to y-axis and 180mm normal to x-axis. 50 mm 50 mm 150 mm 200 mm 150 mm 50 mm 100 mm 350 mm 50 mm 250mm
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with a 4-20mm diamter bars and at the top with 2-16 mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 32.09 MPa and steel yield strength fy=345 MPa for 20mm bars and fy=275 MPa for 16mm bars. Determine the maximum steel area for a tension-conctrolled singly reinforced condition in positive bending with the given material strength.
A rectangular beam 250mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80mm and at the bottom is 70mm. Use concrete strength f’c=21 MPa and steel yield strength fy=415MPa for 20-mm bars and fy=275MPa for 16mm bars. - Determine the limiting tensile stress ratio for a tension controlled condition in positive or negative bending with the given material strengths. - Determine the design moment capacity of the beam in positive bending in kN.m (whole number) - Determine the design moment capacity of the beam in negative bending in kN.m (whole number)
In the column shown, the lower column bars are #8 and the upper ones are #7. The bars are enclosed by ties spaced 12in. on center. If fy = 60000 psi and f'c = 4000 psi, what is the minimum lap splice length needed? Normal weight concrete is to be used for the 12in x 12in column. ,#7 #8
A rectangular tied column carries a factored axial load of 2060 kN. The width of the column is limited to 350 mm and the clear cover of the column is 40 mm. If the concrete compressive strength is 28 MPa, the yield steel strength is 415 MPa, and the steel ratio is 0.02. a. Determine the dimensions of the cross-sectional area of the column. b. Determine the number of 20-mm diameter bars needed for reinforcement. C. Determine the clear spacing of the longitudinal bars.
A rectangular beam 250mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80mm and at the bottom is 70mm. Use concrete strength f’c=21 MPa and steel yield strength fy=415MPa for 20-mm bars and fy=275MPa for 16mm bars. Determine the design moment capacity of the beam in positive bending in kN.m (whole number)
32 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 280 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
A 400x400 mm concrete tied column is to be designed for a factored axial load of 2500 kN. Capacity reduction factor = 0.65. Use the 2010 NSCP. Use fc= 28 MPa and fy = 415 MPa a) The mumber of pieces 20 mm diameter bars for the longitudinal reinforcements is nearest to. b) The maximum allowable spacing (mm) for the 10 mm diameter lateral reinforcements is nearest to. If 16 mm diameter bars are used how many bars are required if it will be placed on equal mumber of pieces on each side of the section. c)
Subject: Reinforced concrete Design- Civil Engineering A rectangular beam has a width of 300mm and an effective depth pf 537.50mm to the centroid of tension steel bars. Tension reinforcements consists of 6-28mm bars in two rows, compression reinforcement consists of 2-22mm bars, fc' = 27.6MPa, fy = 414.7MPa, d'=60mm. The depth of compression block is _mm. Choices: A. 137mm B. 213mm C. 173mm D. 231mm