Answered: lculate the core area in Cm 2 required…

lculate the core area in Cm 2 required for a 1600kVA, 6600/440 V, 50Hz single phase transformer. Assume maximum flux density of 1.2 Wb/m 2 and induced voltage per turn 0f 30V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Related questions

Q: A series resistance-capacitance (RC) circuit is connected to a 230 Volt, 60 cycle source. If the pow...

Q: Using the following information; H =- (cos az - cos a,) a, 4m p a, = a, x a, Find magnetic field int...

A: "According to the Company's policy we will solve only the first part of the question as the second p...

Q: 20Ω Μ 30Ω

Q: Create a truth table based on the 4-state diagram A ,B ,C ,D based on the image

A: This question belongs to digital electronics . It is about writing of truth table from the state dia...

Q: Q2/ Calculate the effective resistance of the following combination of resistances (Req) and the vol...

A: For parallel circuit the voltage is same and for series circuit voltage divides. 6Ω and 12Ω are in p...

Q: A magnetic vector potential A is defined as; - a, Wb/m %3D The total magnetic flux o crossing a surf...

A: Using above identities flux = surface integration (B.ds) Where B = curl (A).

Q: Two similar 6,600-V, three phase generators are running in parallel on constant-voltage and frequenc...

Q: 5. Given the circuit, solve for the 0.2 0 a. Total resistance 0.10 b. Total current 12 V- 1.0 0 c. T...

A: Note:- As, it was asked to solve the (question-5) The solution can be obtained as follows. The given...

Q: Problem 4 Use the definition of complex power to calculate real and reactive power for the load of R...

A: In this question we will find real and reactive power of load with the help of complex power....

Q: Given vectors A = 2a, + 4a, + 10a, and B — 5а, + ag — 3а,, find The angle between A and B at P Р(), ...

A: This problem comes under electrostatics . It is based on the basic laws of vector . With the help of...

Q: A generating station has two 50 Mw units each running for 8,500 hours in a year and one 30 Mw unit r...

Q: a) Recommend a wireless technology for the case where you need to provide seamless highspeed connect...

Q: 1.) A common-emitter amplifier circuit is shown below. The BJT parameter values are B = 100, gm = 24...

A: Brief description: Bipolar junction is known as bipolar because of their is a conduction of electric...

Q: Write the difference between BJT and JFET transistor.

A: BJT is a bipolar junction transistor where both minority and majority carrier in the device and JFET...

Q: You're evaluating the components of a multioccupancy building that won't have an on-site employee. T...

A: In this question we will write about occupant compliance with NEC....

Q: A resistance of 10 Q and a capacitance of 100 µF is connected in series to the parallel combination ...

A: The solution is given below.

Q: Three equal charges (Q1, Q2, & Q3) of +5x10^-6 C (Micro-Coulomb) form the vertices of a triangle tha...

A: To find the total electric field intensity at position of Q2

Q: Why is the circuit critically damped? Explain.

Q: 23. Given a set of capacitors: 7nF, 6nF, 5nF, 4µF, 3pF and 10µF, solve the following problems: a. So...

Q: LED: A student wants to incorporate an LED into a circuit. She finds a bulb that says "11 mA at 4.7 ...

A: Current limiting resistors are generally connected in series with the elements to protect the elemen...

Q: Why is the circuit under damped? Explain.

Q: A 440-Volt shunt motor has an armature resistance of 0.8 2 and a field resistance of 200 2. What is ...

Q: For the circuit below, z, = 2 + j2 N, z, = 4 - j3 N, %3D z, = 8 - j6 N, z, = 10 – j10 2, and z, impe...

A: We have given the following problem

Q: Region 1 (y 0) contains dielectric medium with ɛ2

A: Region 1 (y<0) contains the dielectric medium with ε1=5ε0 and μ1=1.5μ0. While region 2 (y>0) c...

Q: A short circuit test was performed upon a 10-kVA, 2300/230-volt transformer with the following resul...

A: Short circuit test is performed on high voltage side with low voltage side short circuited. Here hig...

Q: Q2\ It is required to use a diodes specified to have a 0.9V drop at a current of 1 mA. The diodes ar...

A: The circuit is as shown below, Forward drop of the diodes is given to be 0.9 Volts. RL = 1.9 kΩ So ...

Q: Given the circuit below. i, (t) = V210 cos(377t). Give your answer in four decimal places if it is n...

A: Student asked to solve only question number 3. So according to student request I have answered quest...

Q: A series circuit consists of a 66.2-uF capacitor and a variable resistor. For what two values of res...

Q: of 4 Page < Figure P6.25 P6.59. Solve for the transfer function H( f )= V out / V in Also determine ...

A: In this question we will find transfer function of given low pass filter and find out its cut off fr...

Q: Q4/ Use Source Conversion technique to find the load current IL in the circuit below.

Q: Express the notations below in rectangular form.

Q: what do you mean by loss of selectivity between two overcurrent relays in adjoining line sections? w...

A: Selectivity- It is a quality of a circuit or an element in which how quickly it responds to a partic...

Q: If the electric field intensity in Region 1 is given as E1 = 35 a, + 25 ax- 15 a, V/m, calculate two...

Q: A series circuit consists of a 66.2-uF capacitor and a variable resistor. For what two values of res...

Q: 6 The area to be considered in using Gauss's Law should be the one where the electric field is perpe...

Q: В8. For the circuit shown in Figure B8, calculate: (a) the frequency and period of the supply voltag...

Q: Using the following information; (cos az - cos a,) a, 4n p H = a, = a, x ap Find magnetic field inte...

A: MAGNETIC FIELD INTENSITY Magnetic field is present around the moving charges .Magnetic field inte...

Q: An electric field of 3.6 x 10° N/C passes through an area of 4.1 cm? perpendicular to the surface. D...

Q: An inductive coil takes a current of 2 A and consumes 160 W when connected to a 240 V AC supply. A s...

Q: For number 12 question Final problem, you will need a test charge to move from one point to another ...

A: The solution is given below

Q: For the combination resistor shown below, calculate the equivalent resistance for the entire circuit...

A: Given, R1=23.7 ΩR2=34.1 ΩR3=74 ΩR4=45 Ω

Q: Figure shows a system of logic gates for y = 1. Which one of the following options is satisfied ? Be...

Q: Given the circuit below. i, (t) = V210 cos(377t). Give your answer in four decimal places if it is n...

Q: GIVEN: REQUIRED: (a) Establish the Current Equations at points x, y and z (b) Establish and simplify...

Q: A boost converter has an input voltage Vb=5V. The average load current is lo=0.5A. The switching fre...

A: In this question , boost converter is given....We have to find out critical inductance and critical ...

Q: A resistance of 100 and a capacitance of 100 µF is connected in series to the parallel combination o...

Q: The faces of the thin square plate in the below figure with side a = 21 are perfectly insulated. The...

A: we have given the following problem

Q: Figure 592 Z2 z1 v1(s) V2(s) R = R1 || R2 or not present V2(s) Ds + Es + F V1(s) Ds + Es + F V2(s) V...

Q: Question-4: Design a Negative-Positive biased clipper circuit that limits the positive output cycle ...

Q: What is PLC?

A: It is a Programmable Logic Controller used in industries to monitor the operations in the industries...

Question

Calculate the core area in Cm 2 required for a 1600kVA, 6600/440 V, 50Hz single phase
transformer. Assume maximum flux density of 1.2 Wb/m 2 and induced voltage per turn 0f
30V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
Bar type CT has the following parameters:CT ratio = 2000/5 AMaximum primary current = 40 kAMaximum flux density in the core = 1.6 TImpedance (Actual burden) = 0.31 ΩCore cross sectional area = 20 cm2Find the maximum burden permissible if no saturation occurs.
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a fluxdensity 3 T, the corresponding relative permeability of iron core is 1500. Determine thenumber of turns in the winding, given that the magnetic flux path has a mean length of 20cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2
The insulation resistance of a single-core cable is 432 Mohm per km. If the core diameter is 2.87 cm and resistivity of insulation is 5.1 x 10^14 ohm-cm, find the insulation thickness.
Problem 1A core with a coil has 240 turns, to generate a flux ø of 0.008482 weber, how much should the current i1 be and what will its direction be? Relative permeabilities: metal 1 of 250 and metal 2 of 375. Core depth 25cm
A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm. The Rtotal is found to be 226.192k At/Wb
1) A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm.a) Calculate the total reluctance, total, of the core
The volume of a transformer core built up of silicon sheet steel laminations is 12000 cm3. If the maximum flux density is 1.0 Wb/m2, find the hysteresis loss in joule/m3 per cycle. The hysteresis coefficient is 250
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a flux density 3 T, the corresponding relative permeability of iron core is 1500. Determine the number of turns in the winding, given that the magnetic flux path has a mean length of 20 cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2. * ROUNDING OFF is ALLOWED only in the final answers expressed up to FIVE (5) DECIMALPLACES.
13.a. Eddy-current loss in the stator core can be reduced by usingA. alloys with low resistivity.B. annealed iron laminations.C. silicon alloys of copper.D. thin laminations of steel.13.b. Which one of the following is damaging to many insulating materials used in alternators?A. Eddy currentsB. SaturationC. CoronaD. Hysteresis
The eddy current loss of a given solid core is 80 W at 50 Hz. What would be the loss of 60 Hz if the core flux density remained the same at the two frequencies. Answer: 115.2 W Use formula: Pe=ke f²
A current of 200 mA passes through a coil of 300 turns wound on a core of length 50 cm, the relative permeability µr of which is 100. Calculate to find the magnetic flux density B setup within the core. Note that: µ0 = 4 π x 10-7 Hm-1