Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flowrate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe issame and equal to 0.05.Ans.Q1= 1.906 m3/s , Q2=1.094m3/sEx.A pipe of dia.=20cm and length 2000m is connects two reservoir havingdifference of water levels as 20m determine the discharge through pipe.If an additional pipe of diameter 20cm and length 1200 m is attached tothe last 1200m length of the existing pipe, find the increase in thedischarge. f=0.015 neglect minor losses.Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/sEx.Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000mfrom the upper reservoir , a small pipe is connected to the pipe line. Thewater can be taken from the small pipe. Find discharge to the lowerreservoira- No water is taken from the small pipeb-100 liter/sec of water is taken from small pipe. f30.005 neglect minorlosses

we are suppose to solve only one question. please post other question as separate question.

Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s

Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For Oil (SG = 0.86, p = 0.025 Ns/m2) flow of 0.3 m3/s through a round pipe with diameter of 500 mm,…

A: Given data: The specific gravity of oil, SG = 0.86. Dynamic viscosity of the oil, µ = 0.025 N·s/m2.…

Q: Q1/Water. p=1,94 slugs/ft and v=0.000011 ft/s. is pumped between two reservoirs at 0.2 ft's through…

Q: find the diameter of pipe of length 2500m when rate of flow of water through pipe is 0.25m cube/sec…

A: Given data: The length of the pipe is; L = 2500 m. The rate of flow through the pipe is; Q = 0.25…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 50 cm respectively.…

Q: The volume flow rate of water is 661,68 liters/min. Calculate the maximum length of the pipe [m],…

A: As comma is placed to every decimal places given to number more than 999 . volume flow rate is too…

Q: Doummate the power an 7- Water to run a Pelton wheel is supplied by a penstock of length e and…

Q: 550mmo 7.88m 2 2.95m Datum

Q: Question 04 4.1 Water discharged from a reservoir into the atmosphere through a pipe 39 m long.…

A: Given, Discharge, Q=2.8dm3/sQ=2.8×10-3m3/s We know that discharge, Q=14πd12v1=14πd22v2 where d1…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 45 cm respectively.…

A: find the friction losses.

Q: 1. Water flows at a rate of 0.020 m3/s from reservoir A to reservoir B through three concrete pipes…

Q: What is the diameter of smalle pipe,

A: For solution refer below images.

Q: In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the…

Q: Given a frictionless flow of water at 125.6 ft^s in a long, horizontal, conical pipe, of diameter 2…

Q: A cast iron pipe of equilateral triangular cross sectión with side length of 20.75" has water…

A: Given Data : Sides of equilateral triangle = 20.75 inch Flowrate = 6000 gallon per minute…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 50 cm respectively.…

Q: A reciprocating pump running at 1 rps and discharges oil (p = 850 kg/m3) at a rate of 366.1 gpm. The…

A: Given:Pump speed, N=1 rpsDensity of oil, ρ=850 kg/m3Oil flow rate, Qact=366.1 gpmBore, D=250 mm=0.25…

Q: Water flows at a rate of 0.185 m3/s through a 150 m long galvanized steel pipe of diameter 200 mm.…

Q: 1. Determine the horsepower output of the turbine assuming an efficiency of 70% in the figure shown.…

A: GIVEN: D = 300 mm Q = 450 L/s = 0.45 m3/s

Q: For the series-parallel system shown in figure, all pipes are 8cm_diameter cast iron. If the total…

A: Given:

Q: In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a…

Q: What is the level h required to deliver a flow rate of 0.425 L/s through the 1.25 cm smooth pipe.

Q: A valve incurs a head loss equal to 2.2 meters length of pipe having a diameter of 8.6 cm and a…

Q: A 120° reducing bend is placed in a horizontal plarje such that the inlet is inclined 30° to the…

Q: A pump delivers water from a tank (A)X water surface elevation=D110m) to tank B (water surface…

Q: A centrifugal pump delivers water at a rate of 0.03 m'/sec to a helght of 18 meters through a pipe…

A: We have given data from the question are, Q=30 L/s=301000 m3/s=0.03 m3/sH=18 m,L=90 m

Q: The volume flow rate of water is 650,53 liters/min. Calculate the maximum length of the pipe [m],…

A: To avoid cavitation, the fluid pressure should not go below its vapor pressure. According to the…

Q: Water discharges through a 300 mm nozzle at the end of a 600 mm p pipe of length 500 m as shown.…

A: The hydraulic grade line (HGL) is the summation of pressure head and datum head. It can also be…

Q: ump has the following characteristic: Volume flow rate (m³/h) Head (m) 23 46 69 92 115 17 16 13.5…

A: A curve is plotted using the above data sets. Since we have two reservoirs and there is a difference…

Q: The water flow (T: with a diameter of D = 0.2 m has a head loss due to friction of hp 20°C) in an…

A: Answer: The volumetric flow rate of water through this pipe is 19.574 litre/sec.

Q: Water flows through main pipe A at 300 kg/s, and then out the double wye with average velocities 2 r…

Q: 1. Determine the flow rate through the venturimeter shown in Fig. if ideal conditions exist. Ans. Q…

Q: What water level H must be maintained in the tank as shown in Fig. P. 3.5.20 to deliver a flow rate…

A: To produce a flow rate of 5×10-4 m3/sec via the pipe, we must determine what water level H in the…

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f=0.0225) oflength…

Q: After analyzing the flow type in a refinery oil (s = 0.8, v= 1.94x10-4 ft2/s) flowing through a…

A: Given, diameter, d=9inch=0.75ftspecific gravity, s=0.8density, ρ=800kg/m3=49.94lbm/ft3kinematic…

Q: Find the cross sectional area of pipe Discharge=77 m3/s Velocity=10 m/s

A: Given data : Discharge Q=77 m3/s Velocity V=10 m/s Required : Cross sectional area of pipe

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: The venturi meter experiment observation readings are 303 mm, 289 mm, and the flow meter reads 174…

Q: The venturi meter experiment observation readings are 318 mm, 288 mm, and the flow meter reads 173…

Q: An air conditioning duct runs straight from fan over 60 m length. It has four equally spaced outlet…

A: Given-Data:- l=60m3Volume=1m3Velocity = 15m/sRegainFactor=0.75 To-Find:- Diameters and Velocities at…

Q: Find the power required to drive the pump which delivers 0.04 m^3/s of water at the height of 20 m…

A: Given data: The flow rate of the water is Q = 0.04 m3/s. The delivery head is h = 20 m. The…

Q: A 120° reducing bend is placed in a horizontal plarge such that the inlet is inclined 30° to the…

Q: A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice pointing upstream and…

A: Data given- d = 300 mm = 0.3 m Mean velocity = 0.8 × central velocity Cv = 0.98 Pressure…

Q: A hydraulic turbine has a gross head of 30 meters and head loss is estimated to be 15% of the gross…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 45 cm respectively.…

A: Friction pressure loss, measured in metres, dissipates the energy necessary to force water through a…

Q: find the diameter through circular duct if the flow rate (0.98 m3/s) and velocity(5m/s) Fullcen Snip…

Q: For a pipe flow Reynold number is found to be 54000. What is the coefficient of friction of the…

Q: EX (3) Find the flow rate (Q1, Q2, Q3), if Qt -20 m3/sec, v- 1.12 10 m2/s. Pipel L (m) D(mm) 100 E…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is
2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow
rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is
same and equal to 0.05.
Ans.Q1= 1.906 m3/s , Q2=1.094m3/s
Ex.
A pipe of dia.=20cm and length 2000m is connects two reservoir having
difference of water levels as 20m determine the discharge through pipe.
If an additional pipe of diameter 20cm and length 1200 m is attached to
the last 1200m length of the existing pipe, find the increase in the
discharge. f=0.015 neglect minor losses.
Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/s
Ex.
Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000m
from the upper reservoir , a small pipe is connected to the pipe line. The
water can be taken from the small pipe. Find discharge to the lower
reservoir
a- No water is taken from the small pipe
b-100 liter/sec of water is taken from small pipe. f30.005 neglect minor
losses

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
A horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil (s.g.=0.88) and the pressure in the smaller pipe is 265 kPa what is the pressure in the bigger pipe neglecting friction?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
1.Compute the lost pressure for a diverging fitting. The flow rate in the 20 cm upstream section is 0.24 m3/s, and the flow rate in the 20 cm branch is 0.24 m3/s. The downstream section has a diameter of 25 cm. Assume a 45° wye.
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
Water temperature = 15 deg C Steel pipe diameter = 25 cmLength of pipe = 450 mRoughness = 3.2 mmHead loss = 7.2 mFind: If water flows through the pipe, find the volumetric flow rate of water.
Estimate the power developed by a hydro project which has a stream of 100 l/s of flow at s 60 m of head. Assume the density of water is 993 kg/m3 and efficiency of the whole setup is 63 %.
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
A 152.4 mm, Schedule 40 pipe line 91.4 m long conveys 3028 l/min of cold water from a pump to a point of discharge 24.4 m higher than the pump. There are four 90° elbow in the line. Find the pumps dynamic discharge head. Use Table of Equivalent Length of Straight Pipe (see image). Please help. Thank you :)
An inclined venturi meter has an entrance of 0.08 m in diameter and throat of 0.02 m in diameter. Calculate the coefficient of discharge when the pressure difference between the entrance and the throat is 173kN/m^2. The venturi meter used to measure the discharge of the 311 dm^3/minute. Throat is 0.46m higher than the entrance.
For the series-parallel system shown in figure, all pipes are 8cm_diameter cast iron. If the total flow rate is 0.026 m3/s find; a-) The flow rate for each pipe b-) Pressure lost between point (A) and (B) note: Take f=0.02 and neglect minor losses.