Note: This is not an assignment question C. For turbulent pipe flow, the pipe can be treated as hydraulically smooth ifEu*etwhere e is the surface roughness. Hydraulically smooth conditions means that surface roughness willnot effect the flow. Why is the limit set to ɛt < 5?

Answered: Image /qna-images/answer/49870c12-da49-4299-b259-1b70f4d829e5.jpg

Answered: -< 5 the surface roughness.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at 20 C. a. What is the velocity of the water (average) in the pipe? b. What is the Reynolds number value? c. Is the flow laminar or turbulent?
Water flows through a 15m pipe with 1.3 cm diameter at 20 l/min. Determine the length of entrance region, le?
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
The following data were obtained for the flow of 20°C water at20 m3/h through a badly corroded 5-cm-diameter pipe thatslopes downward at an angle of 8°: p1 = 420 kPa, z1 = 12 m,p2 = 250 kPa, z2 = 3 m. Estimate (a) the roughness ratio ofthe pipe and (b) the percentage change in a head loss if thepipe were smooth and the flow rate the same.
Answer completely The Fanning equation and the Darcy-Weisbach equation both relate the pressure drop with the dynamic pressure of the flowing fluid in a channel. What is the physical significance of the pressure drop? Why is it needed to be determined?
Gasoline flows through a 1.5 cm diameter at 1m/s. Determine the length of entrance region, le?
A 60-cm water pipe carries a flow of 0.1 m³/s. At point A the elevation is 50 meters and the pressure is 200 kPa. At point B, 1200 meters downstream from A, the elevation is 40 meters and the pressure is 230 kPa. The head loss , in feet, between A and B isA. 6.94B. 15.0C. 20.88D. 100.2
Give another use of the idea of "Flow Rate and the Equation of Continuity."
choose the correct answer Q1A- If the viscose force is dominate in Reynolds number, the flow will be: * a) Laminar flow b) Turbulent flow c) Transition flow d) All the answers Q1B- Chézy and manning equations are controlled in design of : * a) Water pipes network b) Open channels c) Water jet applications d) None of all above
Two oil tanks are connected by two 9-m-long pipes, asin Fig.. Pipe 1 is 5 cm in diameter and is 6 mhigher than pipe 2. It is found that the flow rate in pipe2 is twice as large as the flow in pipe 1. (a) What is thediameter of pipe 2? (b) Are both pipe flows laminar?(c) What is the flow rate in pipe 2 (m3/s)? Neglect minorlosses.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

-< 5 the surface roughness. Hydraulically smooth condition the flow. Why is the limit set to et < 5?