Let a = 4 m, b = 1 m, PB = 30 kN, Pc = 40 kN, and PE = 15 KN. Construct the shear-force andbending-moment diagrams on paper and use the results to answer the questions in thesubsequent partsPBBaPcaPEECalculate the reaction force Ay acting on the beam. (Note: Since Ax = 0, it has been omitted fromthe free-body diagram.)Final answer in kN rounded-off to 1 decimal place

GIVEN DATA- An overhang beam given subjected to point load We have to draw SFD and BMD

Let a = 4 m, b = 1 m, PB = 30 kN, Pc = 40 kN, and PE = 15 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts a PB B a Pc b D a PE E X Calculate the reaction force Ay acting on the beam. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Final answer in kN rounded-off to 1 decimal place

Let a = 4 m, b = 1 m, PB = 30 kN, Pc = 40 kN, and PE = 15 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts a PB B a Pc b D a PE E X Calculate the reaction force Ay acting on the beam. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Final answer in kN rounded-off to 1 decimal place

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.3.10P: The cross section of a composite beam made of aluminum and steel is shown in the figure. The moduli...

See similar textbooks

Similar questions

A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
A wood beam AB on simple supports with span length equal to 10 ft is subjected to a uniform load of intensity 125 lb/ft acting along the entire length of the beam, a concentrated load of magnitude 7500 lb acting at a point 3 ft from the right-hand support, and a moment at A of 18,500 ft-lb (sec figure). The allowable stresses in bending and shear, respectively, are 2250 psi and 160 psi. From the table in Appendix G, select the lightest beam that will support the loads (disregard the weight of the beam). Taking into account the weight of the beam (weight density = 35 lb/ft3), verify that the selected beam is satisfactory, or if it is not, select a new beam.
Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.
Find expressions for shear force V and moment Mat x = 2L/3 of beam (a) in terms of peak load intensity q0and beam length variable L. Repeat for beam (b) but at x = L/2.
A freight-car axle AS is loaded approximately as shown in the figure, with the forces P representing the car loads (transmitted to the axle through the axle boxes) and the forces R representing the rail loads (transmitted to the axle through the wheels). The diameter of the axle is d = 82 mm, the distance between centers of the rails is Z., and the distance between the forces P and R is A = 220 mm. Calculate the maximum bending stress vmaxin the axle if P = 50 kN.
The beam AB shown in the figure supports a uniform load of intensity 3000 N/m acting over half the length of the beam. The beam rests on a foundation that produces a uniformly distributed load over the entire length. Draw the shear-force and bending-moment diagrams for this beam. Repeat part (a) for the distributed load variation shown in Fig. b.
Find expressions for shear force V and moment M at x = L/2 of beam BC. Express V and M in term s of peak load intensity q0and be a m length variable L.
A simple beam with an overhang supports a uniform load of intensity q = 1200 lb/ft and a concentrated P = 3000 lb load at 8 ft to the right of A and also at C (sec figure). The uniform load includes an allowance for the weight of the beam. The allowable stresses in bending and shear are 18 ksi and 11 ksi. respectively. Select from Table F-2(a), Appendix F, the lightest I-beam (S shape) that will support the given loads. Hint: Select a beam based upon the bending stress and then calculate the maximum shear stress. If the beam is overstressed in shear, select a heavier beam and repeat.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
The cross section of a composite beam made of aluminum and steel is shown in the figure. The moduli of elasticity are TA= 75 GPa and Es= 200 GPa. Under the action of a bending moment that produces a maximum stress of 50 M Pa in the aluminum, what is the maximum stress xs in the steel? If the height of the beam remains at 120 mm and allowable stresses in steel and aluminum are defined as 94 M Pa and 40 M Pa, respectively, what heights h and h. arc required for aluminum and steel, respectively, so that both steel and aluminum reach their allowable stress values under the maximum moment?
Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.