Let's say that you are given a network address block as 192.168.16.0/24, and are asked to divide it into five different networks. The largest network will have 80 hosts. What would be the subnet mask for this network? Oa. 255.255.255.0 or / 24
Q: Given a network address of 172.50.0.0 with a needed usable host of 28, What is the maximum number of…
A: Find the required answer given as below :
Q: is a process-to-process protocol that adds only port addresses, checksum error control, and length…
A: TCP: TCP (Transmission Control Protocol) is a standard that defines how to establish and maintain a…
Q: Given an address of 200.10.10.0 with a needed usable host of 16, What is the 7th subnet range?
A: The question is given an address of 200.10.10.0 with a needed usable host of 16, What is the 7th…
Q: Consider the scenario in which one computer sends a packet to another computer by using the…
A: The issue at the transport layer concerns the exchange of packets between two computers. A package…
Q: Based on the information in the graph, we need to design a network addressing scheme that will…
A: Given Data : Number of subnets = 3 Host for subnet = 24 , 60 , 15.
Q: A frame with destination address CC:DD:EE:FF:FF:FF is meant for _____ host(s) in the network. a.one…
A: The host can be of independent and that is only 1, when the frame has this type of destination…
Q: Consider a scenario that is having an IP address 172.17.0.0, you need divide the network into 4…
A: Given: Consider a scenario that is having an IP address 172.17.0.0, you need divide the network…
Q: Assume that a computer transmits a packet to another computer on the Internet at the network layer.…
A: Introduction: Transmission Control Protocol/Internet Protocol (TCP/IP) networks use data packets to…
Q: Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps. The…
A: Given that: The distance between the nodes = 5 meters Transmission rate = 1Mbps = 106bps Propagation…
Q: Homework: Draw a network with the following specifications: (a) Two ring networks with four hosts…
A:
Q: An IP address can be written as a 32-bit number. For a class B network, the two most significant…
A: The answer to this question and its explanation is present in the image attached.
Q: Solve the following questions: a What is the subnetwork address if the destination address is…
A: To find the solution for the following What is the subnetwork address if the destination address is…
Q: Consider the router and the two attached subnets below (A and B). The number of hosts is also shown…
A: Given network is shown below Here two subnets Subnet A and subnet B and these subnet share the…
Q: A subnet mask is a 32-bit number that masks an IP address, and divides the IP address into network…
A: 1) JUMP 2)15.0.0.0 below is the explanation.
Q: Three subnets have the following network prefixes: 57.6.96.0/21, 57.6.104.0/21, 57.6.112.0/21, and…
A: The given networks are: 57.6.96.0/21 57.6.104.0/21 57.6.112.0/21 57.6.120.0/21 Only the second…
Q: Assume a computer transmits a packet via the Internet's transport layer to another computer. At the…
A: The answer is
Q: Can you find any problem with the following statement? "In a network (let Network Address…
A: Given: "In a network (let Network Address 101.10.0.0/25 is using for 120 hosts network) a station is…
Q: Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps. The…
A: The distance (Distance between two host A and B=20,000km (a) distance(Distance) between two hosts A…
Q: Design a classfull network addressing scheme that will supply the minimum number of hosts per…
A: From the Given problem description we see that the ip address : 172.16.0.0 Below are the steps we…
Q: 1. Your company is given the block of addresses at 23.56.192.0/18. You must create 1024 subnets with…
A: We are given the block of addresses at 23.56.192.0/18 and we are asked to create 1024 subnets with…
Q: Can you find any problem with the following statement? Explain. " In a network (let Network Address…
A: To find the network id of an IP address, we need to do AND operation with subnet mask and IP…
Q: Consider a class C network with the subnet mask 255.255.255.41. How many network id (NID) and host…
A: In class C 24 bit network bit and 8 bit are host bit. Subnet mask : 255.255.255.41 in binary:…
Q: For example, let say that your Network 1 needs 30 hosts and you are in a class C network, you would…
A: Part(A) Class A address range is from 0-127. The value of the subnet mask for Class A 255.0.0.0.…
Q: Given a Class C subnet Mask 255.255.255.192. what will be the subnet address and host number for a…
A: IPv4 address are consist of 32 bits. A unique identifier for computers connecting to a network is an…
Q: Network Address Translation, or NAT, was used very often before IPv6 was fully implemented as a…
A: Defined the utility of Network Address Translation(NAT)
Q: Qno 9: Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps.…
A: Given:- Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps.…
Q: Assume a computer sends a packet to another computer through the Internet's transport layer. There…
A: Intro At the transport layer, the question is regarding the interchanging packets between two…
Q: if we have the IP address 192.168.1.0 /24 (class C address) with the pllowing requirements 1. Subnet…
A:
Q: Choose a set of class C, /24 addresses that could be successfully combined into a supernet that…
A: Super netting: It is a process of combining small networks into big networks. It is also called as…
Q: You are asked to create equal-size subnets in the 205.33.44.0 network using subnet mask…
A: Given IP address is 205.33.44.0 Subnet mask= 255.255.255.224(/27) Number of network and subnet…
Q: LOMB R5 20MB 50MB R2, 4MB (R6 10 MB B0MB R4 25 MB 25MB (R7 R3 SMB
A: OSPF LSAs contains useful information, but they do not contain the specific information that a…
Q: Given a subnet mask 255.255.255.240. What will be the subnet address for a host with IP 200.10.5.68?…
A: Given a subnet mask 255.255.255.240. What will be the subnet address for a host with IP 200.10.5.68?…
Q: Suppose a computer sends a packet at the network layer to another computer somewhere in the…
A: Actually, LAN stands for Local Area Network.
Q: rk address of 198.125.50.0 with a needed usable host of 45, What is the custom subnet mask for this…
A: the solution is an given below :
Q: f an organization is given the CIDR address 215.151.48.0/24 and decided to divide its addresses into…
A: The given address belongs to class C where # of network ID bits is 24 and # of host ID bits is 8 For…
Q: Let's say that you are given a network address block as 192.168.16.0/24, and are asked to divide it…
A: The answer is..
Q: There are two hosts a and B, which are connected through router R1. The IP addresses and MAC…
A: Given network contains two hosts A and B which are connected through Router R1. The IP addresses…
Q: Given a class C network address of 197.1.2.0, divides into 32 subnets, what will be the broadcast…
A: IPv4 address are consist of 32 bits. A unique identifier for computers connecting to a network is an…
Q: Given an address of 200.10.10.0 with a needed usable host of 16, What is the custom subnetmask for…
A: The IP given above is an IPv4 and each of the digits can be between 0-255 which means 8 bits to…
Q: Suppose host A is sending a large file to host B over a TCP connection. The two end hosts are 10…
A: Given:
Q: Given a network address of 220.100.100.0 with a needed usable host of 28, What are the assignable…
A: The Classless IP subnetting of 220.100.100.0 begins from the fourth octet of the IP address. To get…
Q: 5. Your company is given the block of addresses at 132.54.129.0/24. You must create 16 subnets with…
A: Given Block of Addresses at 132.54.129.0/24. Number of subnets to create = 16 subnets with an equal…
Q: Suppose a computer sends a packet at the transport layer to another computer somewhere in the…
A: Actually, the question is Suppose a computer sends a packet at the transport layer to another…
Q: Assuming a subnet mask of 255.255.248.0, which three addresses are valid host addresses? (Choose 3)…
A: Here is the solution:
Q: Let's say that you are given a network address block as 192.168.16.0/24, and are asked to divide it…
A: The answer is...
Q: For a network address of 192.10.10.0/28, find: a) default and custom subnet masks b) number of bits…
A: We are given a network address and we have to find subnet masks, subnet bits, number of subnets and…
Q: Suppose two hosts (Host-A and Host-B) are connected through a shared Ethernet bus of 1 Mbps. The…
A: Distance: The distance (Distance) between 2 hosts A and B = twenty,000 km a) The distance…
Q: if we have the IP address 192.168.1.0 /24 (class C address) with the following requirements 1.…
A:
answer only 100% sure
dont post plagiarized content strict aciton take
Step by step
Solved in 2 steps
- An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most signi cant bits are used as a network ID, and the 16 least signi cant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?Computer Science In Python, I am trying to make a client and server code that passes the payload with the requirements. The client has to specify the length of the data packet, up to max, specify how many times to pass the data packet, and specify the server IPv4 address. Both the client and the server need timer functions and compute the time needed to perform the number of sends both the Client and the server need to display the local and remote IPv4 addresses, total time, and bytes per second. Please help, Thanks.
- Berkeley Computer Science example (CS-168): Picture this: there are two hosts (A and B). The two hosts are connected by 50 msec of propagation delay. The bandwidth is equal to 106 B/sec. Note that the hosts use a sliding window where (W = 4, and packet size = 1000 Bytes) with (Selective Repeat). We will ignore the size of ACK and assume that the timer value for each packet is set as (send time + RTT) and retransmission occurs immediately after a timer expires. Make sure to assume that the packets are sent in sequence starting at time 0. How long does it take to successfully receive all 4 packets (P_0, P_1, P_2, P_3). Your answer should be in milliseconds. 1. When there is no packet loss. 2. When the P_1 packet becomes lost, but there is no further packet lossConsider the following non-default subnet masks: (a) 255.255.248.0, (b) 255.128.0.0 . To which IP address class do they pertain?Write down the following in CIDR notation: (a) IP: 150.160.170.180, Subnet Mask:255.255.224.0; (b) IP: 75.80.85.90, Subnet Mask: 255.252.0.0 Three stations A, B, C and D are connected to a common Ethernet hub. Their IPaddresses and subnet mask are respectively: 200.100.50.67, 255.255.255.252;200.100.50.7, 255.255.255.248; 200.100.50.138, 255.255.255.240 and 200.100.50.1,255.255.255.254. Determine which among these stations can communicate with eachother. You need to show all detailed workings.A network configuration of a modem is given as following:LTE interface IP = 77.110.156.22 MASK 255.255.252.0Default GATEWAY = 77.110.156.1Masquerade NAT, and DNS address = 1.1.1.1Local IP setup: 192.168.128.1 MASK 255.255.255.0And, ip route 192.168.128.0 255.255.252.0 192.168.128.254 Devices numbered R1, R2, R4, R5 are routers. PC is a computer.Image of network with interface names such as f1/0 are added. You must use only static IP addreses and static IP routes to configure the network and make PC able to connect (ping) to Modem.
- Given a Class C subnet Mask 255.255.255.192. what will be the subnet address and host number for a machine with IP address 197.1.2.67. Select one: a. second subnet and host 2 b. Third subnet and host number 3 c. second subnet and host 4 d. First subnet and host number 3 e. None f. Second subnet and host number 3. Assume: Your laptop's Ethernet address is 0a:0b:0c:0d:0e:0f, DHCP server address is 131.111.7.3, your IPv4 address will be 131.111.7.121, the gateway's IP address is 131.111.7.1, and Ethernet address is 00:01:02:03:04:05, the network subnet mask is 255.255.255.0.Write the series of protocol/packet exchanges that occur on the wired Ethernet link, up until you can send a single packet to 128.232.0.20. You do not need to describe packets after this packet has left the link. Include ARP and DHCPWrite a program by c programming language for VLSM calculator Input will be: 1) Input by user - IP address[sample- IP address - 192.168.1.10/24]2) Input by user - How many LAN/Networks in your topology [number of 'n'. n can be any numbers]3) Input by user - How many Host/computers in each LAN/Networks [number of 'n' in each topology. n can be any numbers] Output will be:1) Network address with subnet mask, first assignable address, last assignable address, broadcast address and gateway address for each LAN/Networks. Sample Input example for your understanding:- sample IP address - 192.168.1.10/24 ------------------------------------------ 1st LAN/Network : 258 Host/Computers2nd LAN/Network : 200 Host/Computers3rd LAN/Network : 120 Host/Computers...'n' times LAN/Network : 'n' Host/Computers Output example for your understanding:- ----------------------------------------- 1st LAN/Network : [Network address with subnet mask]1st LAN/Network : [first assignable address]1st LAN/Network :…
- Write a code for VLSM calculator by c programming languageInput will be: 1) Enter IP address [sample- IP address - 192.168.1.0/22]2) How many LAN/Networks in your topology [number of 'n'. n can be any numbers]3) How namy Host/computers in each topology [number of 'n' in each topology. n can be any numbers] Output will be:1) Network address with subnet mask, first assignable address, last assignable address, broadcast address and gateway address for each LAN/Networks. Sample Input example for your understanding:- sample IP address - 192.168.1.0/24 ------------------------------------------ 1st LAN/Network : 258 Host/Computers2nd LAN/Network : 200 Host/Computers3rd LAN/Network : 120 Host/Computers4th LAN/Network : 20 Host/Computers5th LAN/Network : 56 Host/Computers...'n' times LAN/Network : 'n' Host/Computers Output example for your understanding:- ----------------------------------------- 1st LAN/Network : [Network address with subnet mask]1st LAN/Network : [first assignable…Write aprogram to find the ip dotted decimal notation conversion from decimal to binary,octal and hexadecimal and vice versa also find the result of NOT and AND operation of ipv4 adresses. a. 114.34.2.8 Find the result of each operation: a. NOT (22.14.70.34) Find the result of each operation: a. (22.14.70.34) AND (255.255.0.0) ALso develop a program to find classes of ip adress and first and last address,subnet mask also. Develop in javaUsing packet tracer, implement a network that has the following components: 1- At least five routers 2- At least 7 subnets 3- At least 12 PCs 4- At least 4 switches 5- Use RIP routing protocol To assign IP addresses of the routers and PCs, use the IP address from your ID as follows Assume your id is 118zyxw, Consider the numbers z, y, x and w as deciemal You have the subnet 118.0.0.0/24 If your ID is 1181234 then the IP is 118.0.0.0/24 Use this subnet to get at least 7 subnets.
