Liquid of mass density p is flowing along a horizontal pipe of variable cross-section, and the pipe is connected with a differential pressure gauge at two points A and B. Show that if (pr-p:) is the pressure indicated by the gauge, the mass m of liquid flowing through the pipe per second is given by, 2p(P1-P2) m = 01 02 where o, 02 are the cross-sections at A, B respectively.

Liquid of mass density p is flowing along a horizontal pipe of variable cross-section, and the pipe is connected with a differential pressure gauge at two points A and B. Show that if (pr-p:) is the pressure indicated by the gauge, the mass m of liquid flowing through the pipe per second is given by, 2p(P1-P2) m = 01 02 where o, 02 are the cross-sections at A, B respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The tank contains air at a temperature of 20∘C∘C and absolute pressure of 800 kPakPa . Using a valve, the air escapes with an average speed of 160 m/sm/s through a 25-mmmm-diameter nozzle. If the volume of the tank is 1.25 m3m3, determine the rate of change in the density of the air within the tank at this instant. Gas constant of the air is R� = 286.9 J/(kg⋅K)J/(kg⋅K). Express your answer using three significant figures.
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: A) Neglecting friction, the volume flow rate of airB) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
A tire having a volume of 3 ft3 contains air at a gage pressure of 26 psi and a temperature of 70°F. Determine the density (slugs/ft3) of the air contained in the tire. For air, R = 1.716 x 103 ft-lb/slug-°R.
The brake mechanism used to reduce recoil in certaintypes of gun consists essentially of a piston attachedto the barrel and moving in fixed cylinder filled with oil.As the barrel recoils with initial velocity v0, the pistonmoves and oil is forced through orifices in the piston,causing the piston and the barrel to decelerate at arate proportional to their velocity; that is, a = -kv.Express a) v in terms of t, b) x in terms of t, c) v interms of x. Draw the corresponding motion curves.
A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the tank is 2m. The tank is subjected to the acceleration of 5m/s^2 along a 30o inclined plane in the upward direction. Under this condition, there is no loss of liquid. determine the slope of free surface determine the pressure at point A and point B
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Determine(a) Thevelocity(m/s)atsectionB.(b) Thepressure(kPa)atpointB.(c) FP (x-direction),(d) FP (y-direction),(e) The magnitude and direction of FRX of the force required to hold the bend in place.(f) The magnitude and direction of FRY of the force required to hold the bend in place.Forces are to be expressed in Newtons.
The truck carries an open rectangular container that is 3.5 m wide, 3.0 m deep and 5.0 m long, contains oil of density 869 kg/m3 to a depth of 2.0 m. If it has a constant acceleration of 6.7 m/s2. Determine the total force(in kN) acting at the rear wall of the container.
A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the tank is 2m. The tank is subjected to the acceleration of 5m/s^2 along a 30o inclined plane in the upward direction. Under this condition, there is no loss of liquid. determine the slope of free surface determine the pressure at presure
The initial pressures at A and B are the same at 103 kPa. If the pressure at the liquid at A (SG1 = 1.25) is increased to 148 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.51 cm, and the inclination of the tube is 18 degrees with respect to the horizontal. Assume unit weight of air to be negligible.
A tank is in the form of a right circular cylinder with hemispherical ends. The overall length of the tank is4 meters and the diameter of the hemisphere is 1 meter. If a pump discharges a fluid whose density is1.2 kg m /Liter in this tank at a rate of225 liters per minute determine a.) Weight of liquid inside the tank ifit is half full. b) total time to fill the tank assuming it is initially empty.
Intravenous infusions are normally flowed by gravity when the fluid bottle is high enough to counteract the blood pressure in the vein and force the fluid to enter, as illustrated in the figure. The higher the height at which the bottle rises, the greater the flow rate of the fluid. a) If the fluid and blood pressures are observed to balance each other when the bottle is 1.2 m above arm level, determine the gauge pressure of the blood. b) If the gauge pressure of the fluid at the arm level needs to be 2038 mm H2O to have sufficient flow, determine at what height the bottle should be placed. Consider the density of blood to be 1058 kg / m3.
If the static pressure of that fluid in the pipeline is 4.3 ´ 104 Pa while its total pressure is 4.7 ´ 104 Pa, determine the kinetic energy per unit volume of the fluid. Assume that the fluid is incompressible and non-viscous. Consequently, calculate the volume flow rate in the pipeline. Take density of the fluid to be 103 kgm-3and the cross-sectional area of the pipeline as 20 cm2.