List the 2 aspects that need to be considered when temperature testing for reliability

Q: mention five Machine tools used in workshops and explanation of the various parameters in Condition…

A: Machine tools used in workshops

Q: Brinell harness experiment is a type of NDT test. Select one: True False

A:

Q: Low cost of investment for breakdown maintenance which after the occurrence of an advanced…

A: Correct option is:

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: April 29, 20 Failure Mode Effective Analysis for Electric vehicles?

A: To plan a failure effective analysis (FMEA) for electric vehicles we should be very thorough about…

Q: Name the four comfort factors.

A: For thermal comfort, below four are the important comfort factors: Temperature Humidity Air quality…

Q: A vehicle's Maximum Gross Weight (MGW) can be found on the New York State registration and is used…

A: True. The MGW tells the Maximum gross weight.

Q: 14- Pentane filled glass thermometer is used to measure low temperature. Select one: True False

A: Thermometer:-  It is device used for the measuring temperature or a temperature gradient.

Q: 10 units of bulb were tested where the normal lifespan is 100 hours 3 units of bulb failed at 10…

A: Failure rate per hr.

Q: Subject - Determine the effects of sound and vibration related to building services and human…

A: Controlling Vibrations         1 Vibration dampening: guards, hoppers, conveyors, tanks... all…

Q: Discuss the steps on how to perform a proper hazard control. Give some examples

A: Hazard Control : Hazard control consists of all necessary steps and practices to protect workers…

Q: State one advantage and disadvantage of compression testing.

A: Compression testing: It is a strength test method of material under compression. For testing the…

Q: Describe the general process used to calibrate a device such as a pressure gauge or a temperature…

A: Pressure guage is a mechanical instrument use to measure pressure of a fluid medium. General time of…

Q: q8   Cleaning  a machine with  compressed air is a general safety precautions considered while…

A: The given statement is false.

Q: Pressure measuring devices like differential manometers are used to measure the pressure difference…

A: Differential U- tube manometer

Q: (a) Discuss what is operate to failure and design out maintenance. (b) Discuss the differences…

A: These are maintenance philosophies Operate to Failure and Design out Maintenance are two maintenance…

Q: a) What is meant by safe design? b) List any four general principles of prevention.

A: a) DESIGN  A design is a blueprint or specification in the form of a prototype, product, or process…

Q: Name TWO (2) types of hardness test.

A: Hardness test- the hardness test is perform to know the hardness of material.it is used to determine…

Q: The pendulum strikes at the front side of the notch in Izod impact test.         Select one:…

A: Pendulum Strike In Izod Test

Q: Give any four significance of API Standard

A: American Petroleum Institute (API) Standard:-  American Petroleum Institute of standards Improve…

Q: The rate of change of viscosity with temperature is known as viscosity index and low viscosity index…

A: Viscosity index(VI) is a dimensionaless number which give the relationship between viscosity and…

Q: Ultrasonic testing is a low sensitivity testing method. a) True b) False

A: Ultrasonic testing is a low sensitivity testing method.

Q: statics and dynamics

A:

Q: Alternation and inspection of equipment are the primary functions of maintenance. Select one: True…

A: The given statement is true.

Q: List six steps involved in performing a visual inspection.

A: Visual inspection is the method of checking for the defects using naked eye. Visual inspection is…

Q: Penetrant testing Procedure below with Dwell time, and Minimum three defect that can be detected…

A:

Q: A- There are good and bad effects of mechanical vibrations. Give five examples of the bad effects of…

A: To explain: The effect of vibration. Concept used: Vibration: Mechanical vibration is defined as the…

Q: True

A: High cycle fatigue is defined as number of cycle more then 1000

Q: manometers are used to measure pressure in pipes. Select one: True False

A: Yes, it is true.

Q: Give detailed description of at least two methods of vibration measurement.

A:

Q: 28. The measurement of a thermocouple can be found directly from its standard data table if ola

A: ANSWER -a)  TRUE

Q: In which method of fault diagnosis ,the whole system will be divided in equal halves ?

A: The output of a measurement system is called as measured value. The above statement is true.…

Q: EXERCISES 3.1) A component experiences chance (CFR) failures with an MTTF of 1100 hr. Find the…

A:

Q: Alternation and inspection of equipment are the secondary functions of maintenance. Select one: True…

A: This statement is false reason given below.

Q: PMM2 means that a machine follows 2nd law of thermodynamics Select one: True False

A:

Q: submit at least 10 hazard symbols and its description used in a workplace. identify the workplace…

A: There are a lot of hazard symbols which are used in industries. Some of them are listed below.

Q: Less staff is required for breakdown maintenance which is carried out as fast as possible to bring a…

A: Let us discuss breakdown maintenance.

Q: Less staff is required for breakdown maintenance which is carried out as fast as possible to bring a…

A: Benefits  Negligible planning is required. The prepare is exceptionally straightforward so it is…

Q: (a). Mention the types of maintenance. Define breakdown maintenance. b). Draw the diagram and…

A: Maintenance  In general, maintenance may be described as attempts to maintain a machine's condition…

Q: State and explain the three fault finding diagnosis in plant machinery

A: following is the answer to the above problem

Q: seconds. If the next inspection is to take place in 30 days, would it be safe to delay the…

A:

Q: 15) Hardness is a very important thermal property that can be measured by the Vickers's hardness…

A: Hardness: It is the ability of a material to resist deformation under the load.

Q: The |type maintenance requires periodical inspection and testing.

A:

Q: An example of a liquid lubricant is graphite that is introduced between two contact surfaces to…

A: An example of a liquid lubricant is graphite that is introduced between two contact surfaces to…

Q: Which of the following will not come under fault diagnosis? a. Replacement O b. Dynamic Testing O c.…

A: Dynamic testing doesn't comes under fault diagnosis . dynamic testing are used to crosscheck the…

Q: What is the difference between reliability for a reparable vs a non-reparable item

A: Repairable systems are different from the non repairable systems. Difference between Reliability for…