load (KN) Elongation (mm) AL 0.5 3-8 7-9 12-9 14-3 15-9 16.9 17-8 19-1 21-2 24-2 26-9 30 32.0 NO S D. 1 0.3 0-5 0-7 0-9 1 1-1 1-3 1-6 1-9 2-2 2-5 28 calculation -compression Stress (6c) = A. compression strain (c) = Lo-Lf -young's Modulus (E)=0C Lo Ec hight = 6-5mm. d = 5.9 mm. Please solve fast Write a table. Write the full 15 numbers

load (KN) Elongation (mm) AL 0.5 3-8 7-9 12-9 14-3 15-9 16.9 17-8 19-1 21-2 24-2 26-9 30 32.0 NO S D. 1 0.3 0-5 0-7 0-9 1 1-1 1-3 1-6 1-9 2-2 2-5 28 calculation -compression Stress (6c) = A. compression strain (c) = Lo-Lf -young's Modulus (E)=0C Lo Ec hight = 6-5mm. d = 5.9 mm. Please solve fast Write a table. Write the full 15 numbers

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced concrete beam has a width of 300 mm and an effective depth of 500 mm with the centroid of tension and compression bars located 70 mm from the bottom of the beam. The compression and tension reinforcements of the beam are 4-20mm∅ and 8-25mm∅ . Use fy =345 MPa and fc'= 30 MPa. Which of the ff. nearly gives the depth of compression block in mm. a. 167.14 b.135.67 c. 126.85 d. 144.87 e. 189.52 Which of the ff. most nearly gives the compressive force of the compression steel in kN. a. 389 b. 400 c. 415 d. 434 e. 455 Which of the ff. gives the ultimate moment capacity of the beam. a. 486 b. 498 c. 512 d. 521 e. 536
The coefficient of friction between blocks A and C and horizontal surfaces are µs =0.24 and µk = 0.2 knowing that MA = 5kg, MB = 10kg and MC = 10kg. Determine, The tension in the cord The acceleration of each block
Given: b = 350 mm d = 550 mm As = 5-20mm dia. f'c = 28 MPa fy = 275MPa Required: 1 Depth of compression block, mm 2 Depth of the neutral axis, mm 3 Nominal moment capacity, kN-m 4 Ultimate moment capacity, kN-m
Q1 / Determine the resulting displacement of pin B. Assume: A1 = A2 = 900 mm², E1 = E2 = 100 GPa, al = a2 = 12x10-6 / ° C, AT = 35 ° C, h = 1200 mm, 0 = 60 °
A 250 mm x 450 mm reinforced concrete beam (Fy = 248 , fc’ = 30 MPa) that is 12 meters long is supported by hinge/roller at ends and midspan. It is reinforced by 4-28mm Φ bars and in compression by 2-28mm Φ bars. Effective concrete cover is 65 mm. 1. Find the depth of rectangular compression block. a. 85.82 mm b. 65.82 mm c. 75.82 mm d. 95.82 mm 2. Find the nominal capacity. a. 105.91 kN.m b. 205.91 kN.m c. 305.91 kN.m d. 405.91 kN.m
d(mm)=125 q(kN/m)=3.0 F(kN)=2.0 T allow(MPa)= 2.5
A rectangular reinforced concrete beam 350 x 550 mm (b x d) is provided with 3H25 bar (As = 1473 mm2) as compression steel. Determine the area of tension steel needed for the beam to attain its full moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 35 N/mm2and fyk = 500 N/mm2and d’ = 60mm. Take until 2 decimal point for each calculation. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167 As ‘ = (M-Mbal) / 0.87 fyk (d-d’) As = Mbal / 0.87 fyk zbal + As’
-6,00 Design a short square tied column to carry a factored axial design load Pu of 750 kips an a factored design moment Mu of 250 ft.-kips. Place the longitudinal reinforcing uniformly in the four faces. Use f, = 5000 psi and fy = 60,000 psi. o. Then P 350-1.9 h2 1.86 30 ao
the service load bending moments acting on a rectangular beam 333 mm wide and 617mm deep are 139.65kn-m for dead load and 91.15kn-m for live load. f'c=29.99moa fy=414mpa p=0.68pbak db=20mm ds=10mm stirrups are sipral calculate the D/C ratio in percentage
A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20 C with v=0.005 m^2/s and sp.gr.=0.9. Find the force exerted by the oil in the shaft.
A reinforced concrete T-beam has the following properties: flange width, b = 1370 mm; flange thickness, tf = 130 mm, width bw = 300 mm, effective depth, d = 610 mm, As = 2950 mm², f’c = 28 MPa, fy = 414 MPa. 1. Which of the following most nearly gives the depth of the compression block of from the top of the beam? a. 37.5 mm b. 95.5 mm c. 45.8 mm d. 115.4 mm 2. Which of the following most nearly gives the total compressive force in concrete? a. 1380 kN b. 1220 kN c. 1840 kN d. 1540 kN 3. Which of the following most nearly gives the ultimate moment capacity of the section in kN-m? a. 450 b. 550 c. 750 d. 650
distributed load = 13kN L = 3m (3L = 3 x 3m = 9m) F = 7 kN.