load (KN) Elongation (mm) |AL0.53-87-912-914-315-916.917-819.121-224-226-93032.0900-30-50.70-911-31-61-92-22-S28URLineCalculation-compression Stress (6c) = &1compression strain (c) = Lo-Lf-young's Modulus (E)=Echight= 6-8 mm.d = 5.9 mmWrite the fulltable. 15 fieldsRequirements and results:1. Redraw it suitable scale, the recorded loaddisplacement diagram.2. Determine the yield stress and modulus ofelasticity.3. Compared between tensile and compression.Please solve fast

Hey there, As multiple questions are posted in a single picture. As per our guidelines we can only…

load (KN) Elongation (mm) AL S 0.5 d. 1 3-8 7-9 12-9 14-3 15-9 16-9 17-8 19.1 21-2 24-2 26-9 30 32.0 0.3 0-5 0-7 0-9 1 1-1 1-3 M 1-6 1-9 2-2 2-S 28 Calculation -compression stress (6c) = A compression strain (c) = Lo-Lf Lo -young's Modulus (E) = hight = 6.5mm d = 5.9 mm. Ec Write the full table. 15 fields Requirements and results: 1. Redraw it suitable scale, the recorded load displacement diagram. 2. Determine the yield stress and modulus of elasticity. 3. Compared between tensile and compression. Please solve fast

load (KN) Elongation (mm) AL S 0.5 d. 1 3-8 7-9 12-9 14-3 15-9 16-9 17-8 19.1 21-2 24-2 26-9 30 32.0 0.3 0-5 0-7 0-9 1 1-1 1-3 M 1-6 1-9 2-2 2-S 28 Calculation -compression stress (6c) = A compression strain (c) = Lo-Lf Lo -young's Modulus (E) = hight = 6.5mm d = 5.9 mm. Ec Write the full table. 15 fields Requirements and results: 1. Redraw it suitable scale, the recorded load displacement diagram. 2. Determine the yield stress and modulus of elasticity. 3. Compared between tensile and compression. Please solve fast

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1 / Determine the resulting displacement of pin B. Assume: A1 = A2 = 900 mm², E1 = E2 = 100 GPa, al = a2 = 12x10-6 / ° C, AT = 35 ° C, h = 1200 mm, 0 = 60 °
-6,00 Design a short square tied column to carry a factored axial design load Pu of 750 kips an a factored design moment Mu of 250 ft.-kips. Place the longitudinal reinforcing uniformly in the four faces. Use f, = 5000 psi and fy = 60,000 psi. o. Then P 350-1.9 h2 1.86 30 ao
A reinforced concrete beam has a width of 300 mm and an effective depth of 500 mm with the centroid of tension and compression bars located 70 mm from the bottom of the beam. The compression and tension reinforcements of the beam are 4-20mm∅ and 8-25mm∅ . Use fy =345 MPa and fc'= 30 MPa. Which of the ff. nearly gives the depth of compression block in mm. a. 167.14 b.135.67 c. 126.85 d. 144.87 e. 189.52 Which of the ff. most nearly gives the compressive force of the compression steel in kN. a. 389 b. 400 c. 415 d. 434 e. 455 Which of the ff. gives the ultimate moment capacity of the beam. a. 486 b. 498 c. 512 d. 521 e. 536
A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20 C with v=0.005 m^2/s and sp.gr.=0.9. Find the force exerted by the oil in the shaft.
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
The reinforced concrete column is reinforced with 6 – 28 mm Ø bars as shown. Steel yield strength fy = 414 MPa and concrete strength fc’ = 21 MPa.1. Determine the nominal balanced load.a. 1721.252 kN c. 1821.225 kNb. 1921.253 kN d. 1521.522 KN2. Determine the nominal balanced eccentricity.a. 362.544 mm c. 352.544 mmb. 372.544 mm d. 382.544 mm3. Determine the nominal balanced moment.a. 677.326 kN.m. c. 777.321 kN.m.b. 312.852 kN.m d. 563.285 kN.m.
reinforced concrete T-beam has an effective depth of 600 mm and is reinforced at the bottom with steel area of 4926 mm2. The web width is 300 mm and has a flange thickness of 100 mm. The beam has a span of 6 m and has a spacing center to center equal to 1.8 m. ??′=21 MPa ??=415 MPa. Determine the following:a. Effective width of the flangeb. Depth of the compression blockc. Nominal moment capacity of the beam
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
A 250 mm x 450 mm reinforced concrete beam (Fy = 248 , fc’ = 30 MPa) that is 12 meters long is supported by hinge/roller at ends and midspan. It is reinforced by 4-28mm Φ bars and in compression by 2-28mm Φ bars. Effective concrete cover is 65 mm. 1. Find the depth of rectangular compression block. a. 85.82 mm b. 65.82 mm c. 75.82 mm d. 95.82 mm 2. Find the nominal capacity. a. 105.91 kN.m b. 205.91 kN.m c. 305.91 kN.m d. 405.91 kN.m
note: SN = 18, to the topload will be 118kN
A T beam for a floor system has a slab thickness of 100mm and total depth of 550mm. bw=300mm. The beam has a span of 6m with a spacing of 2.4m center to center. The beam carries a live load moment of 184 kN.m and dead load moment of 84 kN.m f'c = 20.7 Mpa, fy= 413.7. Steek cover = 65mm A.Determine the effective flange width (m) B.Determine the depth of concrete compression block (mm) C.Determine requires steel area,(mm^2)
Calculate Tension BD if P = 100 kN.