Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully observe the proper sign of the radical involved.) Set a = 38 in. Answers: x = y = i i in. in.

Q: Label the components in the pneumatic circuit

A:

Q: Use cylindrical coordinates to find the indicated characteristic of the cone shown in the figure.…

A:

Q: A cycle has a pressure compression ratio of 7.8. If the isentropic compression of air has an initial…

A:

Q: In a truss it is assumed that the members are joined by: Select one: O a. smooth pins O b. welding O…

A: In order to avoid the creation of bending strains, this is believed to be the case. Straight parts…

Q: A pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve…

A:

Q: What is the maximum amount of energy released when a 5 kg sample ofcoal from McDowell, West Virginia…

A: Write the higher heating value of coal from McDowell, West Virginia. HHV=36.2 MJ/kg

Q: Determine the x- and y-coordinates of the centroid of the shaded area shown.

A:

Q: A wall with a brick and concrete layer is shown in the figure. The wall has a leng 15 m and 6 m…

A: Given:length of wall, l=15 mheight of wall, h=6 mkb=1.3 W/m.Ktb=75mmkc=2…

Q: atch the picture with the correct Miller indices describing the planes shown: 3 a₁ 4 Faz E D E 2₁ a₁…

A:

Q: Find the applied force Work done=88812 J Displacement=1000 m

A:

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: The rotation in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 10 mm in radius and…

A:

Q: Consider the frame below consisting of 3 beams with pins at B, C, and D. Beam CDE is 7 meters long,…

A: (a) Calculate the equivalent force for the distributed load.

Q: Find the pressure at depth of 2 m from free surface of water

A: Given : depth of water from free surface, h = 2 m To find :  pressure at depth h

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 9" y 1 Answers: 9" (X,Y)= (i…

A:

Q: A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum.…

A:

Q: The 56-kg crate is stationary when the force P is applied. Determine the resulting acceleration of…

A:

Q: PROCESS INSTRUMENTATION AND CONTROL Mention the level measurement system, which protects the DP…

A: Introduction; Differential pressure(DP) transmitter are used for measuring pressure reading.

Q: A pair of spur gears with 20° full-depth involute teeth, the pinion shaft is connected to a 10 kW,…

A:

Q: Determine the tension in the cable

A: Given  Mass of the box=400 Kg Acceleration=2 m/s2 Gravitation g=9.81m/s2   Find Determine the…

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: A frame ABC is supported in part by cable DBE that passes through a frictionless ring at B. Knowing…

A: given Tension = 385 N

Q: .A crane is to raise a load of 25,000 N at an acceleration of 1 m/s2 through a 6 x 19 wire rope…

A: Given data: a=1 m/s2n=6×19=114Er=80 kN/mm2D=960 mmd=32 mm Need to determine the bending load of the…

Q: A spring is stretched 6 in by a mass that weighs 8 lb. The mass is attached to a dashpot mechanism…

A:

Q: Find the force applied Work done=554.44 J Displacement=50 m

A: Given data: W=554.44 Jd=50 m Need to determine the applied force.

Q: Find the spring constant if a 20. N force stretches a spring 2.0 m.

A: Given data : Force F=20 N Extension X=2 m   To find : Spring constant

Q: b) For the truss in the figure below, determine the zero-force members and give a short explanation…

A:

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

A:

Q: Measurements of 10 min each give gross and background count rates, respectively, of 72 and 54 cpm,…

A: Given data: Time taken = t = 10 min Gross count rate = G = 72 cpm Background count rate = B = 54 cpm…

Q: The 160-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right…

A: Given:m=160lbmc=20lba=0.30g

Q: The spring's stiffness coefficient is k and the unstretched length is s. A particle moves from…

A:

Q: 2.0 Engine oil at 100°C and a velocity of 0.25 m/s flows over both surfaces of a 0.8-m-long flat…

A:

Q: a) What is a truss? Explain shortly in your own words, and illustrate with one example. b) For the…

A: Answer (a): Truss: A fixed frame of members which is used to support something (roof, bridge) is…

Q: Determine the velocity of Block B in the figure if Block A has a downward velocity of 8.78 m/s. Y₁ =…

A: Given data: ◆ The downward velocity of the block A: VA = -8.78 m/s ...(negative means downward) ◆…

Q: Q-2. A cylindrical specimen of alloy steel having an original diameter of 12 mm is subjected to a…

A: Write the given data. Di=12 mmF=60 kNDinst=10 mm∆L=10%L

Q: Figure 5.15 in the text gives a schematic of a Carnot cycle operating with a H₂O liquid/vapor with a…

A:

Q: Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Given: P = 5.5 kN.…

A:

Q: Q3 A translational mechanical system can be simplified in schematic diagram as in (a) Draw the free…

A: Given: Let us consider the given figure, To find: The system's free body diagram. The system's…

Q: Given a fourbar linkage with the link lengths L1 - d - 100 mm, L2-a- 50 mm, L3-b-120 mm, L4c-80 mm.…

A:

Q: When testing the landing gear unit of a space vehicle drop tests are carried out. Figure 2.17 is a…

A:

Q: In an ECM process for machining iron, it is desired to obtain a metal removal rate of 1 cm³/min.…

A:

Q: dvantages and disadvantages of fixed wing and rotary wings

A: Advantages and Disadvantages of Fixed wing and Rotary wings   Advantages of fixed-wing Increased…

Q: What is the main reason for conducting a 3-point stroke test on the pneumatic control valves on the…

A: The correct option is A.

Q: The rotational EoM about the mass center of the rigid body indicates that the sum of moments due to…

A: Motion of body is 1. Translational motion 2. Rotational motion 3. Translational and rotational.

Q: A 100-kg box is towed to move horizontally from rest by a constant force P=200 N. The kinetic…

A: Given:m=100 KgP=200 Nμk=0.1θ=30°g=9.81m/s2

Q: Prove the following two equations: Strengh of Material G= K = E 2(1+v) E 3(1-2v)

A:

Q: what is the discharge in each pipe i

A:

Q: S HAVE BEEN OPERATED FOR 100 URS. WHAT IS THE MEAN TIME B ISTANT FAILURE RATE FOR THE AB

A: given:total operating time =100hrtwo machine failed in 100hr

Q: Your company has been assigned to evaluate two pumps; Pump Megatron and Pump Omicron to be used at…

A: For ARAU- Group 1, Group 5Pipe diameter, D=2.03 cm=0.0203 mPipe roughness, ε=0.25 mm=0.25*10-3 mLoss…

Q: Find the pressure at depth of 2 m from free surface of water

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.