Find the air-fuel ratio of a four-stroke, single-cylinder, air-cooled enginewith fuel consumptionatime for 10 cc is 20.4 s and ay ansumption timefor 0.1 m3 is IS 3Find also brabre bultfuel consumption in g/kW 4.3 3 brake thermalefficiency. Assıunhe the density of air as 1.175 kg/m³ &ck specific gravityof fuel to be 0.7. The lower heating value of fuel is 43 MJ/kg and thedynamometer constant is 5000.(imm "he load is 17 kg at theof 3000 rpm.

Answered: Image /qna-images/answer/d15d0101-2856-44f5-bfc7-caaab452556e.jpg

Answered: lower heating value of fuel is 43 MJ/kg…

Engineering

Mechanical Engineering

lower heating value of fuel is 43 MJ/kg and t

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 10 kg steel bar at 627 °C is dropped in 100 kg of oil at 30 °C. The specific heats ofsteel and oil are 0.5 kJ/kg K and 3.5 kJ/kg K, respectively. Determine the change inentropy of the steel, oil, and the universe.
Carbon dioxide has a specifi c heat ratio of 1.30 and a gasconstant of 189 J/(kg ∙ ° C). If its temperature rises from20 to 45 ° C, what is its internal energy rise?( a ) 12.6 kJ/kg, ( b ) 15.8 kJ/kg, ( c ) 17.6 kJ/kg, ( d ) 20.5 kJ/kg,( e ) 25.1 kJ/kg
An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the density at the inlet, ρ1 __________(kg/m3)
1. A horizontal "hot air blower" consists of a fan, an electrical heating element and a nozzleThe power input to the fan is 50 J/s and the power input to the heating element is 1.44 kJ/s. The air enters the fan with negligible velocity at a pressure of 1 bar and a temperature of 20 C, the volumetric flow rate being 0.5 m3/min. After passing over the heating element, the air leaves the nozzle with a velocity of 25 m/s and a pressure of 1.1 bar. Treating the complete arrangement as a steady flow system and ignoring any heat loss from the system, determine: (a) The mass flow rate of air entering the fan in kg per second(b) The kinetic energy of the air leaving the nozzle per second(c) The change in enthalpy of the air occurring per second between entering the fan and leaving the nozzle(d) The temperature of the air as it leaves the nozzle.(e) The density of the air as it leaves the nozzle(f) The flow area at the nozzle exit.Take R = 0.287 kJ/kgK and cp = 1.005 kJ/kgK
Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
A forced draft centrifugal fan draws air at 1.32 cubic meter/sec towards a combustion chamber of a steam generator. The static pressures are 15mm. water below atmospheric at suction and 10mm. water above atmospheric at the discharge. The inlet duct is 30cm in diameter and the discharge duct is 27cm in diameter. The fan mechanical efficiency is 70%. The air is measured at 25 degrees Celsius and 760mmHg. Determine: a. the Air Power in kW 0.664 0.464 0.546 b. the Brake Power in kW 0.546 0.464 0.664 c. the static efficiency 50.00 48.77 52.03
Evaluate and compare the work and heat transfer when 0.75 kg of air, at a pressure of 1.5 barand a temperature of 27 °C, expands in a closed thermodynamic system to three times itsinitial volume (i) according to Boyle’s law and (ii) according to Charles’ law.The characteristic gas constant for air is 287 Jkg-1K-1 and its specific heat capacity at constantvolume is 718 Jkg-1K-1. Explain the differences in the answers to the two techniques.
Approximate the theoretical power in wind moving at a speed of 6 m/s with an air temperature of 40°F striking wind turbine with a 10ft diameter rotor (use mass density = 1.277 kg/m3). a.300.89 W b.27.95 W c.10,831.90 W d.None of these e.1,006.32 W
Can you solve the question step by step ? What is the conversion type and energy conversion efficiecy of wind turbine based on the practically achieved limit ?a) Kinetic to electrical / 90% b) Kinetic to electrical / 59%c) Thermal to electrical / 60% d) Gravitational to electrical / 90%
A thermodynamic steady flow system receives a 4.56 kgm per min of fluid where p1=137.90 kPa, v1=0.0388 m^3/kgm, ϑ1=122 m/s, and u1= 17.16 KJ/kgm. The fluid leaves the system at a boundary where p2= 551.6 kPa, v2= 0.193 m^3/kgm, ϑ2= 183 m/s, and u2= 52.80 KH/kgm. During pasage through the system the fluid receives 3000 J/s of heat. Determine the work.
A 30-kW motor drives a fan and delivers air through a duct 1.0 m x 1.0 m at 11.684 cm WG static pressure and 2.159 cm WG velocity pressure. The density of air is 1.20 kg/m³ and the density of water is 1000 kg/m³. Determine: 2. The capacity of fan, m3/s 3. Fan efficiency, %
In a hydroelectric potential, the upstream level is at an elevation of 1000 m and the downstream level is at an elevation of850 m. Knowing that the useful flow for use is 13 m³/s and the total efficiency of the system (losses ofload + turbine efficiency + generator) is 87%, tick the alternative that contains the electrical powergenerated (consider g = 9.8 m/s² and the density of water as 1000 kg/m³):ALTERNATIVESa) 16,625 MW.b) 16625 MW.c) 13.33 MW.d) 1.66 MW.e) 1.33 kW.