LSS ANSWER ASAPPP Which is correct about spherical shell? a It has the same formula as hoop stress b The wall of the pressurized spherical vessel is subjected to uniform comporessive stress in all directions c It has the same formula as the tangential stress d The wall of the pressurized spherical vessel is subjected to uniform tensile stress in all directions

LSS ANSWER ASAPPP Which is correct about spherical shell? a It has the same formula as hoop stress b The wall of the pressurized spherical vessel is subjected to uniform comporessive stress in all directions c It has the same formula as the tangential stress d The wall of the pressurized spherical vessel is subjected to uniform tensile stress in all directions

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.27P: -27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile...

See similar textbooks

Similar questions

Given the stress cube below, represent the Mohr Circle, demonstrating the stepsfollowing:a) Calculation of main stresses and directions;b) Calculation of stresses in a plane of rotation ?, clockwise;c) Circle of Mohr.
Pls do not solve the question. My question is how can i determine the the stress axis, for instance sigma(x) or sigma (y)? In the question, the Moment (Mz) is causing the holder's y axis to bend. So shouldnt the normal stress be sigma(y) = -P/A + MzY/I instead of what the answer has given sigma(x) = -P/A + MzY/I. sigma (x) should be = 0 instead of signma(y). am i right?
Pls do not solve the question. My question is how can i determine the the stress axis, for instance sigma(x) or sigma (y)? In the question, the Moment (Mz) where the z-axis is the centroid is causing the holder's y axis to bend. So shouldnt the normal stress be sigma(y) = -P/A + MzY/I instead of what the answer has given sigma(x) = -P/A + MzY/I
Pls do not solve the question. My question is how can i determine the the stress axis, for instance sigma(x) or sigma (y)? In the question, the Moment (Mz) is causing the holder's y axis to bend. So the normal stress should be sigma(y) = -P/A + MzY/I instead of what the answer has given sigma(x) = -P/A + MzY/I? sigma (x) should be = 0 instead of signma(y). Am i right?
Explain the deconvolution of the principal stress state into the hydrostatic and deviatoric stress components and the importance of the deviatoric stress
The state of stress at a point can be described by σx = 40 MPa , σy = 64 MPa , and τxy = 18 MPa . A second coordinate system is rotated by θ = 25 ∘ A) What is the normal stress in the direction of the x′-axis? B) What is the shear stress in the y′-direction for the faces with a normal in the x′-direction? C) What is the normal stress in the direction of the y′-axis?
2. (a)A single thick-walled cylinder h2as an inner radius of 100 mm and an outer radius of 155 mm. The cylinder is subjected to an internal pre2 ssure of 65 ????/?? and an external pressure of 25????/?? . (i) Calculate the hoop and radial stress inside and outside of the cylinder. (ii) Sketch the 3D Mohr’s Circle of a point on the inner surface of the cylinder and label the principal stresses (include coordinates values). (iii) If the cylinder is made of a copper alloy with yield strength of 200 MPa; verify whether the cylinder will fail using the Von Mises Criteria and calculate the Factor of Safety. (b) To increase the FOS to the standards value, another cylinder is shrunk-fitted to make a compound cylinder. When the internal pressure load remains unchanged, the maximum hoop stress in the inner cylinder of the compound cylinder has been found to be reduced by 5% of the original value(i)Calculate the interface pressure at the common radius of the compound cylinder. (ii)Assume the…
In a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} = 80MPa , Ty = 40 MPa . What is the maximum shear stress (in MPa) at the point?
A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium cylinder having an outside diameter 150mm and inside diameter 100mm thereby causing a contact pressure of 20MPa. What is the largest internal pressure that can be applied to the assembly without exceeding a tangential stress of 100MPa at the inner surface. Ans: Pi = 97.5MPa answers must tally
Do the principal stresses represent the maximum and minimum normal stress?
Help ASAP Determine the tensile stress in the upper plate at section b-b in mpa 3decimals
Choose the stress to which the size correction factor should be applied in Soderberg's formula. a. Mean stress b. Yield stress c. Variable stress d. Endurance limit stress Clear my choice

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

GET THE APP

About FAQ Academic Integrity Sitemap Document Sitemap

Contact Bartleby Contact Research (Essays)High School Textbooks Literature Guides Concept Explainers by Subject Essay Help Mobile App

GET THE APP

Privacy

Your CA Privacy Rights

Your NV Privacy Rights

About Ads

Manage My Data

bartleby, a Learneo, Inc. business

	a	It has the same formula as hoop stress
	b	The wall of the pressurized spherical vessel is subjected to uniform comporessive stress in all directions
	c	It has the same formula as the tangential stress
	d	The wall of the pressurized spherical vessel is subjected to uniform tensile stress in all directions