Answered: A single shear lap-joint connection is…

A single shear lap-joint connection is shown in the figure, If P-10,825 N, d-22 mm, and t-38 mm, determine the tensile stress in the upper plate at section b-b, in MPa? a be 300mm →P 9 6 c

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.4P: .4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the...

See similar textbooks

Related questions

Q: Determine the moment of inertia for shaded area about x and y axis. 60 mm 30 mm MATHalino.com 45 mm…

A: Draw the given diagram with sections.

Q: A house is to be maintained at 20°C when the outside air is at -25°C. It is determined that 1800 kJ…

Q: Draw shear force and bending moment diagrams for the beam and loading in the figure.

A: Let HA and VA be the horizontally forward and vertically upward reaction at support A respectively…

Q: Draw shear force and bending moment diagrams for the beam and loading in the figure.

A: Let "C" be the center of the beam. Let the reactions at point A and B are RA and RB respectively.

Q: MEMBER AB AC AD BD CD CE DE DF EF EG EH FH GH FORCE (KN) 60 kN-> E 120 kN- 120 kN- C A G 3 m H F D B…

Q: A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the…

Q: 7.5 m 7.5 m 7.5 m Which of the two configurations above should a company use if it plans on using a…

A: In this problem, we have to calculate the heat transfer through the wall of the both the…

Q: Convert the reading of pressure to kpa.

Q: A spark-ignition engine has a compression ratio of 10:1. The total intake volume of the cylinders is…

Q: The muzzle velocity of a projectile is 1,500 fps and the distance of the target is 10 miles. What…

Q: Q.3. The right-angle bar shown in figure (3) is supported by a pin at B and a roller at C. What is…

Q: Suppose a long bone is idealized as a solid cylinder with a diameter of 0.03 m. During a torsion…

Q: In case of negative work the angle between the force and displacement is O 45° O 180° O 90° O 0°

Q: A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm.…

Q: a. A newly installed tire with a perfect tire pattern without any wear issue is shown in Figure 1…

Q: 1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A…

Q: Determine the distance "a" for which the largest absolute value of the bending moment of the beam is…

A: First calculate the reactions. Then draw the bending moment diagram

Q: Air is flowing steadily in an insulated duct. The pressure and temperature measurements of the air…

A: In an insulated duct, we know the air is moving steadily. The question gives the air pressure and…

Q: Q2-a) determine the advantages of power screw. h b-A shaft is to transmit 50 KW at 1200 rpm.. The…

Q: Determine the force in each member of the Pratt roof truss shown in Figure 1-94. 10 kN 10 kN 10 kN B…

Q: Which among the following best describes the s-t graph of a freely falling body? Linear Quadratic…

A: Given question: Which among the following best describes the s-t graph of a freely falling body.The…

Q: b. Consider a system that consists of a piston-cylinder device with an attached linear spring,…

A: Introduction: The work done by the expansion of the gas volume is considered when the…

Q: Knowing that the tensor has been adjusted so that the tension in the frame AD is 850 N, determine…

Q: MEMBER AB AC AD BD CD CE DE DF EF EG EH FH GH FORCE (KN) 60 kN- 120 kN- 120 kN- E C A G 3 m H F D BO…

Q: Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation…

Q: For the given vectors V₁ and V₂, determine V₁ + V₂, V₁ + V₂, V₁ - V₂, V₁ V₂, V₁ V₂. Consider the…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Question 4 The following table lists molecular weight data for a polytetrafluoroethylene material.…

Q: A turbine of 9000 B.H.P. is working under a head of 25 m and runs at 100 R.P.M.- What will be the…

Q: Explain briefly the casting process of a metal and the process of extrusion of aluminum

A: The casting process is the main process of the production department of the engineering. This…

Q: In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480°C. The condenser is at 32°C. For an…

Q: What is the mass, in ounce mass, of the object below? Hint: A and B are parallels respectively.…

A: We have to calculate the mass for the given body. The material is aluminum

Q: B BC is brass. The rod is fixed at its ends and subjected to a torque of T = 400 Nm. The steel…

Q: The state of stress at a point in a member is shown on the element in Figure (1). Determine the…

Q: Question 1 a) As a specialist in a company expert in providing the upgrade for vehicle ride…

Q: The surface tension of the water in air in approximately 0.0756 N/m. If the atmospheric pressure is…

A: It is very basic question of fluid mechanics portion. Topic- Surface tension Used concept is…

Q: Construct a simple hydraulic circuit and indicate appropriate locations for accumulators given the…

Q: Determine pressure?

A: Given data; Force.F=4000 NDiameter=40 cm=0.4 m Find pressure?

Q: Determine the internal forces at point J, with alpha = 0°

A: Introduction: Internal forces: External forces acting on structure elements such as poles, beams,…

Q: Determine the height of an oil column of specific gravity 0.8 in 1) meter of Hg 2) in meter of oil…

Q: Which of the following need NOT be reflected in a sketch when using the Linear Momentum Equation? a.…

A: For part 3Given Dtatala=1.5mspan=9mVa=7.5m/sScale ratio=1/10 ***As per company policy we are…

Q: Discuss drying and milling machineries

A: Drying milling machinery’s Milling machine

Q: Q3 A thin rod of 3 cm length having a thermal diffusivity coefficient (a) of 0.835 cm²/s is…

Q: A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm…

A: Given data: Cycle : Reheat steam cycleThrottle Pressure = 13580 kPaReheat Pressure = 37.50308414…

Q: T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm…

Q: An SUV hauling a trailer is travelling at 25 m/s when the driver hits the brakes. The 1.4 MT trailer…

A: Given : m1=1.4MT=1400 kgm2=1.6 MT=1600 kgF1=4500 NF2=5500 NV=25 m/s To find : what is the braking…

Q: 1. A rectangular block made of steel and a circular shaft made of steel have the same structural…

A: 1 A rectangular block made of steel and a circular shaft made of steel has the same structural…

Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 202.65…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A 9-in solid shaft has the same cross-sectional area as the hollow shaft of the same material with…

Q: 0.3 m B (0) AB 12 rad/s 0.6 m 30° II IV D The velocity at point B is 3m/s towards the left. a. What…

A: given; velocity of B towards left (VB)=3m/sAB=0.3mBD=0.6mθ=300

Q: A glass tube of internal diameter 3 mm is immersed in mercury. The angle of contact of mercury with…

A: A glass tube with an internal diameter of 3 mm is immersed in mercury, with a contact angle of 130…

Question

Help ASAP Determine the tensile stress in the upper plate at section b-b in mpa 3decimals

A single shear lap-joint connection is shown in the figure, If P -10,825 N, d-22 mm, and t = 38 mm, determine the tensile stress in the upper plate at section b-b, in
MPa?
P
a be
300mm
-tee
teeeto
a b c
+P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane of the joint and the faces of the boards must be between 10° and 40f. Under a tensile load P, the normal stress in the boards is 4.9 MPa. (a) What axe the normal and shear stresses acting on the glued joint if a = 20°? (b) If the allowable shear stress on the joint is 2.25 MPa. what is the largest permissible value of the angle ct? (c) For what angle a with the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A solid circular bar having diameter d is to be replaced by a rectangular tube having cross-sectional dimensions d × 2d to the median line of the cross section (see figure). Determine the required thickness tminof the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A short column constructed of a W 12 × 35 wide-flange shape is subjected to a resultant compressive load P = 25 k having its line of action at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses d1and d2., respectively, in the column. Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a C 10 × 15.3 is attached to one flange, as shown.
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights
A standpipe in a water-supply system (see figure) is 12 ft in diameter and 6 in. thick. Two horizontal pipes carry water out of the standpipe; each is 2 ft in diameter and 1 in. thick. When the system is shut down and water fills the pipes but is not moving, the hoop stress at the bottom of the standpipe is 130 psi, (a) What is the height h of the water in the standpipe? (b) If the bottoms of the pipes are at the same elevation as the bottom of the stand pipe. what is the hoop stress in the pipes?
A circular post, a rectangular post, and a post of cruciform cross section are each compressed by loads that produce a resultant force P acting at the edge of the cross section (see figure). The diameter of the circular post and the depths of the rectangular and cruciform posts are the same. For what width b of the rectangular post will the maximum tensile stresses be the same in the circular and rectangular posts? Repeat part (a) for the post with cruciform cross section. Under the conditions described in parts (a) and (b), which post has the largest compressive stress?
A short column with a wide-flange shape is subjected to a compressive load that produces a resultant force P = 55 kN acting at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses asand o^., respectively, in the column, Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a 120 mm X 10 mm cover plate is added to one flange as shown.