Due to the applied loading, the element at point A on the solid shaft in Figure is subjected to the state of stress shown. Determine the principal stresses acting at thispoint using Mohr circleM12 ksi6 ksiB. Determine the minimum principal stresses (ksi) acting at this point using Mohr circle

σx=Normal stress in x-direction=-12 ksi→Normal stress in x-direction is compressive stress.σy=Normal…

Answered: M т 12 ksi + 6 ksi

Engineering

Mechanical Engineering

M т 12 ksi + 6 ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.26P: An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to...

See similar textbooks

Related questions

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

Q: Question One: Derive expressions for determining the change in length for the following bodies P+ b.…

Q: A steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN in the…

Q: The weight of the crate is 50 kg and the spring constant is 200 N/m in DB. Use g= 9.81 m/s2.

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given that: Strain of the bar = ε = γy3E γ = specific weight = 2.1 lb/in3 L = length of the bar = 16…

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

Q: The torsional deformation of a steel shaft is to be 1° in a length of 600 mm. The design shear…

Q: :A normal stress of 20 ksi is to be transferred from one plate to another by riveting a plate on…

Q: Determine the equivalent spring stiffness constant of the following spring in series and parallel.…

Q: If the width of the wedge used in the 3 cm diameter shaft, which transmits the motion received from…

A: Width of wedge, w=8mm=0.8cm Length of wedge, L=27mm=2.4cm Diameter of shaft, d=3cm Motor power,…

Q: 25. A pressure vessel containing gas at 250 psi has an outer diameter of 12 inches and a thickness…

Q: Shear stress has units:

A: The units of shear stress are like the units of any other type of stress. The unit for shear stress…

Q: 1. A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and…

A: This question is related with the pure torsion equation.

Q: 0 MPa. Using the distortion-energy and maximum-shear-stress theories, termine the factors of safety…

Q: A shaft subjected to torsion experiences a pure shear stress t on the surface. The maximum principal…

Q: -600 mm 150 1350 N A

Q: 78. A motor driving a soiid circular steel shaft transmits 40 kW of power at 500 rpm. If the…

A: Given, Power transmitted by shaft = P = 40 kW = 40000 W Rotational speed of shaft = N = 500 rpm…

Q: 1500 N Q: A shaft made of 1006 steel (CD) is required to transmit a power of 100 kW at 300 r.p.m.…

Q: 1) The curve of stress versus time on the cross section of engine connecting rod is shown in the…

A: Given data: Maximum stress, σmax = 78.61 N/mm2. Minimum stress, σmin = -10.75 N/mm2. Calculate the…

Q: A body is subjected to multiple applied forces and moments. The force present on a 10°m area with a…

Q: 20 ksi 40 ksi 60 ksi The differential element above represents the state of plane stress at a point…

A: As per given question Which of the following best represents the orientation of the maximum in-plane…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given data: γ=2.0 lb/in3y=2.8 inL=14 inE=20000 ksi Need to determine the change in length of the bar…

Q: 350 MPa. Using the distortion-energy and maximum-shear-stress theorie determine the factors of…

A: Given: To determine: FOS according to maximum shear stress and distortion energy theory

Q: A thin 3 m × 1 m sheet is being stretched along its length by a normal stress of 7.0 MPa. The…

A: GIVEN DATA SHEET OF DIMENSION 3m*1m E=100 GPa STRESS =7MPa POISSON'S RATIO =0.27 WE HAVE TO FIND %…

Q: 2. A brass sleeve with an inner diameter of 200mm and an outer diameter of 300mm is pressed onto a…

A: Given DataP=16.8MPaEb=110GPavb=0.32Es=210GPavs=0.30r=100+δmmdi=200mmdo=300mm

Q: Which of these factors doesn't affect the stress of a wire? O Diameter O Original length O Load…

A: The stress for any material or wire is It means the stress depends upon diameter, radius or the…

Q: Question One: Derive expressions for determining the change in length for the following bodies P. b.…

Q: Evaluate each of the following and express with SI units having an appropriate prefix: (a) (50 mN)(6…

Q: (i) Maximum normal stress the (ii) Maximum shear stress theor (iii) Distortion energy theory

A: Kindly check the graph below.

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given that: strain = ε = γy3E γ = 2.3 lb/in3 y = 2.4 in L = 6 in E = 24000 ksi It is required to…

Q: A steel rails have a small gap between them to allow thermal expansion. If the length of each steel…

Q: How much fluid is required to raise the pressure in a thin cylinder of length 3 m, internal diameter…

A: This question is related to the thin cylinder problems. In the case of a thin cylinder, there are…

Q: Find the diameter of the propeller shaft, which has to transmit power of 1.5 kW at 8 Hz without…

Q: mparison with the other loads, determine its diameter. Take e factors for bending and torsion as 2…

Q: The displacements in an elastic material are given by: M(1 – v²) M(1 + v)v M(1 – v?) U1 = - -X1X2;…

A: Three disqusional strain rel atmosphere∈xx=∂y∂x, Eyy=∂Y∂y, ∈22=∂ω∂z

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: 0. A pressure vessel containing gas at 250 psi has an outer diameter of 12 inches and a thickness of…

Q: A thick wall pipe with an inner diameter of 120mm and an outer diameter of 180mm is subjected to…

A: Given data as per question Inner diameter =120mm Outer diameter =180 mm E =200 Gpa G =77 Gpa σy=250…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

Q: In machine design we usually compare the equivalent stress of the component with the: a) Allowable…

A: In machine design we usually compare the equivalent stress of the component with the: a) Allowable…

Q: A body is subjected to multiple applied forces and moments. The force present on a 10 m area with a…

Q: The line joining ou (ultimate strength of the material) on mean stress axis and oe (endurance limit…

Q: stress-strain diagram of a certain material is shown below. Determine the modulus of toughness of…

Q: Choose correct answer: A mild steel rod of 15mm diameter that is 1.5.m in length is elongated by…

Q: 12. A horizontal shaft AD supported in bearings at A and B and carrying pulleys at C and D is to…

Q: 50 MPa 60 MPa 60 MPa 50 MPa

Q: A tube is used as shaft wherein 90 kW of power is transmitted. If its outer and inner diameter are…

Q: A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with…

A: Givendi=12cmdo=16cmP=10kg/cm2n=5σy=64ksi

Question

Due to the applied loading, the element at point A on the solid shaft in Figure is subjected to the state of stress shown. Determine the principal stresses acting at this
point using Mohr circle
M
12 ksi
6 ksi
B. Determine the minimum principal stresses (ksi) acting at this point using Mohr circle

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1:-Given data

VIEW

Step 2:-Constructing the Mohr's circle

VIEW

Step 3:- Calculating the centre (C) & Radius (R) of Mohr's circle

VIEW

Step 4:- Finding the Maximum Principle stress & Minimum Principle stress

VIEW

Step 5:-Mohr's circle are given below

VIEW

Step 6:-Result

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
• - 7.4-7 An element on the surface of a drive shaft is in pure shear and is subjected to stresses ??xy= 2700 psi, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an element oriented at a counterclockwise angle ?= 52° from the y axis. (b) The principal stresses. Show all results on sketches of properly oriented elements.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see figure). It is known that one of the principal stresses equals 6375 psi in tension, (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented clement.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
The normal and shear stresses acting on element B are ??x= -46 MPa, sy= -13 MPa, and txy= 21 MPa (see figure for Problem 7.2-10). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
-9The stresses acting on element B in the web of a wide-flange beam are found to be 14,000 psi compression in the horizontal direction and 2600 psi compression in the vertical direction. Also, shear stresses of magnitude 3800 psi act in the direct ions shown (see the figure for Problem 7.2-9). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.