1. A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the maximum shear stress in MPa.
Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…
A:
Q: A mild steel shaft transmits ‘P’ kW at ‘N’ r.p.m. It carries a central load of 900 N and is simply…
A: Given data, Central load W= 900 N allowable shear stress = 42 MPa The maximum tensile or…
Q: The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy…
A:
Q: Two short shafts having identical diameters of 38.0 mm. and rotating at 400 RPM transmitted 26.5 kW…
A:
Q: A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube…
A: a. At inner surface: from the given data, Shear strain,
Q: 41 КРа 4X КРа 27 КРа 2Z kPa D 350 А 8Y KPa 450 88 КРа B E For the state of stress as shown in…
A:
Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…
A:
Q: Q1-A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…
A:
Q: The stal block Shown below is Subjected to a normal stress Of 100 Mea and 85 MPa Aogether with a…
A:
Q: Rod AB is fixed at side A with a length of 500m and a diameter of 20m. On side B, the rod…
A:
Q: Q2 A solid circular bar ABC consists of two segments, as shown in figure 2. One segment has diameter…
A: The diameter of the shaft can be determined by two criteria 1) Shear stress 2) Angle of twist Both…
Q: A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter…
A: Given Data Diameter of drill bit is : d=5.79 mm=5.79×10-3 m Resisting torque is : T=0.36 N·m…
Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…
A: Calculated the principal stresses and maximum in-plane shear stress and calculated the smallest…
Q: timber beam, 80mm wide by 60mm high, is subjected to a vertical shear load of V = 40KN. Determine…
A: Given:b=80 mmh=160 mmV=40 KN
Q: QUESTION 1: 1.1 A punch for making holes in steel plates of 8 mm thick, is shown in figure 1, has a…
A:
Q: 3. If the ultimate shear strength of steel plate is 45,000 psi, what force is necessary to punch a…
A: Given data:
Q: 2. A plane element in a body is subjected to a compressive stress of 80 MPa accompanied by a shear…
A:
Q: Calculate the shearing stress on the 8-mm-diameter bolt at A. Assume single shear. B D 60° 60° 25 cm…
A:
Q: Q3) A bronze helical spring composed of 10 turns of 1.0-inch diameter wire on a mean radius of 3…
A: GIVEN:no. of turns, N=10diameter, D=1inradius, R=3inload, P=750lbG=6X106psithere given that the…
Q: 2. A prismatic bar under an axial load produces a tensile stress of 75MPa on a plane at an angle of…
A: Calculated normal and shearing stress in all faces of the element at an angle of 50 degrees.
Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…
A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress
Q: A spring was made by a steel wire of 25 mm diameter around a 175 mm diameter cylinder. determine the…
A:
Q: 40 60 A circle of 200 mm dia. is drawn on a mild steel plate before it is subjected to two mutually…
A: Given, d = Diameter of the circle = 200 mm σx= Normal stress in horizontal direction = 160 MPa σy=…
Q: 55 mm (71) allow = 100MPa 14.37 x10° mm (12) allow 60 MPa %3D 40 GPa (1) 70 mm 37.71 x10° mm 75 GPa…
A:
Q: 8. Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…
A:
Q: A 24 mm diameter shaft 0.8 m long is twisted through an angle of 1.8 degrees. What is the stress…
A:
Q: A bar of dimension 130 mm x 50 mm x 45 mm, is subjected to an axial pull of 90 kN. The measured…
A:
Q: e 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is…
A: Given:h=3 mt=6 mmD=300 mmT=25 kN.mF=3 kNG=78 GPaζallow=60 MPa
Q: 4. Given a shear stress of T35 MPa and a shear modulus of G-75 GPa, the shear strain is most nearly…
A: Given data : Shear modulus is denoted by G Shear stress is denoted by ζXY Required : Shear strain
Q: If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d…
A:
Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…
A: We are restricted to solve one question at a time. Please ask other questions in the next post.…
Q: 1. A solid aluminum alloy disk with uniform thickness has an allowable speed of Wall = 40,000 RPM, a…
A:
Q: Copper has a rigidity modulus 45 GPa. A cube of copper with 500 mm sides i tubjected to a shear…
A:
Q: 26. If ơ, = 50 ksi, oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…
A: Given: The stress along x-axis, σx = 50 ksi The stress along y-axis, σy = 10 ksi The shear stress,…
Q: subjected to a shearing force of 715N on its top cylindrical face. If the dowel has a diameter of…
A:
Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…
A: Given that: c = 720 mm u = 1.7 mm v = 3.5 mm α = 31o and β = 590 It is required to determine the…
Q: A thin cylindrical shell with D/t ratio equal to 40 subjected to an internal pressure of 2 N/mm. The…
A:
Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…
A:
Q: A bronze tire (thickness=12mm, width= 110 mm, internal diameter=800 mm) was heated and shrunk onto…
A:
Q: 36. A steel bar is heated from room temperature to 80oC while it is free to expand. The bar will…
A: Internal resistance offered by the object per unit normal area when external force is applied is…
Q: The state of plane-stress at a point is given by σx = -200 MPa, σy = 100 MPa and txy = 100 MPa The…
A: Data given- σx = -200 MPa, σy = 100 MPa txy = 100 MPa
Q: The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of…
A:
Q: Figure 1.1 shows a thick cylinder with inside radius of r;=94 mm and outside radius ro =136 mm was…
A:
Q: 1. If o, = 20 ksi, o, = 10 ksi, and txy = 30 ksi, what is the absolute maximum shear stress for the…
A: Calculated absolute maximum shear stress.
Q: (b) Shear stress in pin B. The cross-sectional area of a 7-mm-diameter pin is: 4-7 mm' 38.485 mm Pin…
A: Here, we will see 1.What is double shear 2.The effect of double shear 3.Its significance in given…
Q: t (0) is 0.15°/
A: given:γmax=500×10-6 rad
Q: 1) Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW…
A: Given dataPower trasmitted by the shaft P = 7.5kWPerimssible shear stress for the shaft,bolt and key…
Q: A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length.…
A: Givend=6mmdecrease in lenght ∆L=3.96%×LG=602 Mpaμ=0.20
Q: 1. A flange coupling connects two shafts to transmit 40 kW at 900 rpm. The flanges of the coupling…
A:
Q: A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and…
A: To obtain the magnitude of the shear force on the various fibers of the beam, we must use the pure…
Q: A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in…
A:
Q: A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the…
A: GivenThickness pf the plate t=0.60inshear stress τ=31ksid=0.5ina=2.75in
1. A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the maximum shear stress in MPa.
I need the answer asap pls
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 1 images
- A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
- A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
- A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
- A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.