Machine Design Gear centerGear center0.516142.51.1811.31.751.751.31.1811510171141Figure.1: Gear reduction shaft (Dimensions in inches)2. Bearing selection is a crucial step in the design of gear reduction system. You work for a machinerydesign company and your role is to analyse and design the gear reduction system on a new line offarming equipment. Your manager asked you to select the appropriate cylindrical roller bearing thatsatisfies the load rating of the existing application, where the shaft design engineers calculated reactionson the right side of the shaft to be Ry = 183.1 lbf and R2 =-861.5 lbf.The gear reduction system shaft is designed to rotate at 1200 rev/min, with a desired bearing life of 15kh at a 95 percent reliability in each bearing, assuming distribution data from manufacturer 2 in Table11-6. Use an application factor of 1.2.(a) Obtain a Basic Dynamic Load Rating for a cylindrical roller bearing at the right end.(b) Use an online bearing catalogue of SKF and NSK to fill out the data sheet below for the indicatedbearing types that satisfies the needed Basic Load Rating and the geometry requirements.ManufacturerBearing typeload Limiting speedManufacturer designatedBasicstaticratingserial numberSKFrollerCylindricalbearing, double row,full complementCylindricalbearing, single rowSKFrollerSingle-rowcylindricalbearingsNSKroller

Ry = 183.1 lbfRz = -861.5 lbf Speed =1200 rev/min Life-time = 15 kh = 15000 h Reliability, RD = 95%…

Answered: Machine Design

Engineering

Mechanical Engineering

Machine Design

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The driving sprocket runs at 225 rpm with a center distance of approximately 500 fpm. The transmission efficiency between the engine and the driving sprocket is 85%. 1.1 Determine the pitch and width of chain to be used. 1.2 Determine the number of teeth in each sprocket and the pitch diameters.
In a single-stage gearbox consisting of helical gear pairs, input speed ng= 900 rpm, input power P1=16 kW, the number of teeth of the pinion gear z1= 20, the number of teeth of the second gear wheel z2= 61. gear wheelmaterial is 20MnCr5, for this material: σem=230 N/mm2, pem=1500 N/mm2 and E= 2.1.105 N/mm2is (Helix angle: β=180; grip angle: α=200; factor of safety: S=1.5; form factor: Kfn=2.7; dynamic loadfactor: Kd=1.25; width factor: ψm=12; clutch ratio: ε = 1.6). (20p)a) Calculate the modulus of the gear pair.Module according to root fracture:(p1)Module according to tooth surface crushing:(p2)(Standard module values: 1 – 1.5 – 2 – 2.5 – 3 – 3.5 – 4 – 5 – 6 – 7 – 8 mm)b) Dimension the gears (Diameters of section circle, head circle and base circle, distance between axes). Pay attention the units
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.
n Mukwano Industries, a shaft assembly shown in Fig. 2 is driven by a flat belt at location A and drives a flat belt at location B. The drive belt pulley diameter is 300 mm; the driven belt pulley diameter is 500 mm. The distance between sheaves is 800 mm, and the distance from each sheave to the nearest bearing is 200 mm. The belts are horizontal and load the shaft in opposite directions. Determine the size of the shaft using Distortion Energy Theory (DET) and the types of steel that should be used. Use a safety factor of 10. Also, provide a free-body diagram as well as moment and torque diagrams
The gears of a gear wheel with a module of 4 mm, width of 60 mm and number of 18 teeth were broken during operation. If the gear wheel is made of cast iron (GG-25), with what torque is it loaded? Given: Speed factor Kv= 1.25; ku
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
A certain farm equipment which requires 2200 N-m torque at 708 rpm has a diesel engine that operates at 1601 rpm as its prime mover. A No. 60 roller chain with a total length of 60 pitches and a small sprocket with 23 teeth are to be used with an operating temperature to remain constant at 45 degree C. Determine (a) the no. of teeth of the larger sprocket, (b) the pitch diameter of the smaller sprocket in mm, and (c) the pitch diameter of the larger sprocket in mm. Express your answer in 3 decimal places.
As seen in the figure, a construction machine is rotated by a drive mechanism consisting of belt-pulley and spur gear mechanisms. Engine power P = 5.5 kW ; engine shaft speednm = 1500 rpm ; drive pulley diameter Dt = 16 cm ; diameter of the opposite pulley Dk = 55 cm ; number of pinion teeth z1 = 21 ; number of teeth of the counter gearz2 = 60 ; pulley mechanism efficiency ηk = 0.95 ; Since the efficiency of the gear mechanism is ηd = 0.97: a) Find the output shaft speed nç and the torque Mç on this shaft.b) The force on the taut arm of the belt S1 = 450 N;coefficient of friction μ = 0.3 ; If the winding angle α = 160⁰, is the frictionally transmitted moment Ms sufficient to compensate for the Mg moment on the input shaft? Calculate.
A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in diameter, at a speed of 300 rpm. Power is drawn from the shaft using belts attached to pulleys A and C. (Use the table if necessary) (a) Draw the torque diagram of the driven shaft. (b) What is the safety factor of the driven shaft? Answer: 5.22 (c) Determine the angle of torsion of pulley C with respect to pulley A. Answer: -1.88°
A set of gears is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor, depicted below. The gear on the motor shaft is a 10-pitch pinion, has 18 teeth, and drives at 1200 rpm clockwise. The driven gear has 72 teeth. The motor has failed and is to be replaced with the only motor available, a 600 rpm motor with an 8-pitch pinion. Specify the set of commercially available 20⁰ spur gears, by number of teeth (N3and N4), that would result in the same conveyor speed and can be used without modification to the mounting (the center distance must not change). Find the number of teeth N3 on the pinion (drive) gear (teeth): Find the number of teeth N4 on the driven gear (teeth):
Q.8 A pair of helical gears in which teeth on pinion are 20 and on gear are 30, the normal module is 5 mm and normal pressure angle is 20°. The helix angle is 30°. The pinion is provided 5 kW at 720 rpm. Determine various forces on the teeth.