Marked out of 1.00Flag questionA fluid jet (S=1.4) of velocity V, =20 m/st%3D20m/simpinges normal to a flat plate whichmoves to the right at velocity V =15 m/s.Find the horizontal force required to keepthe plate moving at constant velocity, thejet area is 3 cm.Noude

Answered: Marked out of 1.00 Flag question A…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A two-dimensional sheet of water, 10 cm thick and movingat 7 m/s, strikes a fi xed wall inclined at 20 ° with respect tothe jet direction. Assuming frictionless fl ow, fi nd ( a ) thenormal force on the wall per meter of depth, and fi nd thewidths of the sheet defl ected ( b ) upstream and ( c ) downstreamalong the wall.
How are large tanks treated in fluid mechanics, conservation mass, conservation momentum and Bernoulli Equation?
The cylindrical container in Fig. is 20 cm in diameterand has a conical contraction at the bottom with an exithole 3 cm in diameter. The tank contains fresh water atstandard sea-level conditions. If the water surface is fallingat the nearly steady rate dh/dt ≈ - 0.072 m/s, estimate theaverage velocity V out of the bottom exit.
Water at 20 ° C fl ows steadily through the tank in Fig.P3.101. Known conditions are D 1 = 8 cm, V 1 = 6 m/s, andD 2 = 4 cm. A rightward force F = 70 N is required to keepthe tank fi xed. ( a ) What is the velocity leaving section 2?( b ) If the tank cross section is 1.2 m 2 , how fast is the watersurface h ( t ) rising or falling?
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
A circular cylinder is fitted with two surface-mounted pressuresensors, to measure pa at θ = 1808 and pb at θ = 105°.The intention is to use the cylinder as a stream velocimeter.Using inviscid theory, derive a formula for estimating U∞in terms of pa, pb, ρ, and the cylinder radius a.
Consider air flowing past a hemisphere resting on a flatsurface. If the internal pressure is pi, findan expression for the pressure force on the hemisphere. At what point A on the hemisphereshould a hole be cut so that the pressure force willbe zero according to inviscid theory?
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
What is importance of complex Analysis in Fluid Dynamics? Find the Magnitude at any velocity in a two dimensional motion?
Air at Ma1 = 2.0 and p1 = 100 kPa undergoes an isentropicexpansion to a downstream pressure of 50 kPa. What is thedesired turn angle in degrees?
As seen in the figure, a 6 cm diameter water jet (r=1000 kg/m3) hits a plate with a 4 cm diameter hole on it. Some of the jet passes through the hole and some of it deviates. Determine the horizontal force required to hold the plate in place.
Consider the function f = ay - by 3 . ( a ) Could this representa realistic velocity potential? Extra credit : ( b ) Could itrepresent a stream function?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Marked out of 1.00 Flag question A fluid jet (S=1.4) of velocity V, =20 m/st %3D20m/s impinges normal to a flat plate which moves to the right at velocity V =15 m/s. Find the horizontal force required to keep the plate moving at constant velocity, the jet area is 3 cm. Noude