Problem 2Given:0.75 mt0.4 mMass of car:1400 kgD1.25 mH m-2 m--- 1.5 m→-2 m-Mass of trailer:800 kgBraking force at C (µc= 0.40) is applied and causes skid.0.75 m0.4 mFREE TOROLL-FREE TOROLL|DH m--2 m-+1.5 m--2 m-1.25 mDetermine the reactions at B, C, and D.Note: Pin supports can resist both vertical and horizontal forces.

Answered: Image /qna-images/answer/e5ace587-d2df-4991-a7d2-14ffc03718b6.jpg

Answered: Mass of car: 1400 kg B H m- C -2 m- +…

Mass of car: 1400 kg B H m- C -2 m- + 1.5 r Mass of trailer: 800 kg Braking force at C (uc= 0.40) is applied and causes skid.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes and the hydraulic pressure that should be sent to the piston. Piston's diameter is d = 30 mm.
A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 3. The center-to-center distance is 8 ft. The angular speed of the small pulley is 1850 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, F1a, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes
A double-drum winder is used as a stage hoist for the sinking of a vertical shift. The stage is suspended in the vertical shaft by two winding ropes in double purchase, the fixed ends being anchored in the headgear. Each rope has a strength of 890 kN when new, and a mass of 5.38 kg/m. The empty stage has a mass of 18360 kg. The minimum factor of safety permitted for ropes is 5 at discard, but allowance must be made for 5% deterioration before discard. The shaft is being sunk to a depth of 1830 m below the headgear sheaves. Calculate the maximum mass load that can be placed on stage, including persons and material.
Estimate the rolling resistance force (Fr) for a truck with a mass (M) of 41000kg on a flat asphalt road with a rolling frictional coefficient of 0.033. Assume gravity = g = 9.81 m/sec squared
A 1855 kg car has a velocity of 100 km/h when the brakes are fully applied. Assume modern traction control eliminates tire skidding. Determine time and distance to stop the car if dry-pavement static friction coefficient is 0.8.Creat a conclusion for this problem.
A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock conditions where Ks= 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axesare parallel and in the horizontal plane. The shafts are 8 ft apart. The 6-in driving pulley rotates at1750 rev/min in such a way that the loose side is on top. The driven pulley is 18 in in diameter. Thecoefficient of friction is 0.8. Analyze the centrifugal tension Fc and the torque T.?
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
1. A triple-thread Acme-form power screw of 50 mm major diameter is used. The nut makes 1.5 turn per cm of axial travel. A force of 600 N is applied at the end of a 850 mm wrench used on the nut. The mean diameter of the collar is 90 mm. If the coefficient of friction at the thread and at the collar are 0.15 and 0.13, respectively. Determine the weight that is being lifted.
A 300 HP crawler tractor is pulling a wagon of 25 cu yd capacity equipped with highpressure tires. The weights of the crawler tractor and the empty wagon are 25 tonsand 15 tons respectively. The haul road is well maintained and compacted earth.Select highest figure in range for rolling resistance. The coefficient of traction is0.75. Half of the weight of the crawler tractor and half of the weight of the loadedwagon need to be considered in the slippage check. No penetration occurs as thesurface is hard enough. The average temperature and barometric pressure at thesite location are 30oC and 56.00 cm of Hg respectively. The drawbarpull producedby the tractor at standard conditions is given in the machine’s manual as 15,000 kgin first gear. What is the gradability of the tractor/wagon combination if the wagon isloaded with dry earth? Take a gradability safety factor of 85%.
A slider crank mechanism operates at 5 m/s and applies a force of 40 N to the slider. The slider weighs about 3 kg and the coefficient of friction is the same at the top and bottom. The slider has a dimension of 0.6 m x 0.2 m. Design a lubrication system that will separate the slider with its cylinder.
A ladder of length 5 m is resting against a smooth wall, its point of contact being just below a first floor window. The bottom of the ladder rests on the ground and the coefficient of friction between the ladder and the ground is 0.3. A person of mass 75 kg climbs the ladder, which has a mass of 4 kg. The bottom of the ladder is at the point of slipping, outward from the wall, just as the person reaches the mid-point of the ladder’s length. Draw a free body diagram of the ladder and calculate the maximum frictional force opposing the slipping motion. In addition, determine the angle of inclination (θ) of the ladder, when the person is at the mid-point and the ladder is on the verge of slipping.