A motor is driving a solid circular steel shaft transmits40kW of power at 500 rpm. If the diameter of the shaft is40 mm, The maximum shear stress in the shaft is

Given; Motor driving a solid circular steel shaft transmits, P =40KW Speed,N=500 rpm If the diameter…

Answered: maximum shear stress in the shaft

Engineering

Mechanical Engineering

maximum shear stress in the shaft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: What general trend did you observe from set-ups 1 to 2? Support your answer by using the data…

A: From setup 1 to 3, we observe that the initial velocity of the Marble A was varied. Ignoring all the…

Q: The forces acting on a 1-ft length of a dam are shown in Figure 1-62. The upward ground reaction…

A: Given data as per the question Horizontal force at A side =12500 lb Vertical force =30000 lb The…

Q: 500 kilograms of dressed chicken enter a chiller at 10°C are frozen and chilled to a final…

A: Given: m = 500 kg t = 20 hrs latent heat = 250 kJ/kg and specific heat for different regions…

Q: A sandbag is released from a hot air balloon that is ascending vertically at a constant speed of…

Q: e Normal component of acceleration of a moving object in space time t is given by a = t and the…

A: Given, (rho) = 25t an = t Normal component of acceleration, an = v2/(rho) t = v2/

Q: "Selection is done through analysis of function and properties specification" has something to do…

Q: In a two stage compression with intercooling and flash gas removal design, the evaporator pressure…

A: The intermediate pressure: Pintermediate = 500 kPa

Q: Q2. An object moves from rest in a straight path with acceleration 2 m/s² until it travels a…

Q: he roller coaster car has a mass of 700 kg, including its passenger. If it starts from the top of…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: If FA=8 kN and FB = 5 kN, find the resultant force, find the components of the moment about point o,…

A: Solution: Given data: FA = 8 KN ,FB =5 kN

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: Q4. A stone is thrown upwards from the edge of a cliff 18m high as shown in figure (1). It just…

Q: The main of purpose of pumps is to transfer fluid from one point to another. If that's the only…

A: A pump is used to move fluids from one place to another. It just creates fluid flow; it does not…

Q: The rod OA rotates in the horizontal plane such that e = 0.57t³ radian, and collar B is sliding…

A: The radial acceleration of the collar: arad = -969.334 mm/s2

Q: he roller coaster car has a mass of 700 kg, including its passenger. If it starts from the top of…

A: Drawing the free body diagram, ∑Fn=man;N+7009.81=700v2ρ ............ 1When the roller coaster…

Q: The beam is subjected to the uniform distributed load shown. Draw the shear and moment diagrams for…

A: For the given beam, the point in section AB where shear force changes sign (x2 metres from A) is to…

Q: Problem 1 Many luxury automobiles have thermostatically controlled air-conditioning systems for the…

A: Draw a block diagram for the system.

Q: 9. The frame shown in Figure 1-67 is supported in pivots at A and B. Each member weighs 50 lb per…

Q: Problem2- A tram weights 120KN and tractive resistance being 5 N/KN. Calculate the ram at a uniform…

A: Weights,W=120KNTractive resistance=5 N/KNUniform Speed =20KmphEfficiency=80%To-Find:-Power required…

Q: R12-4. The v-t graph of a car while traveling along a road is shown. Determine the acceleration when…

Q: Select the health regulation prescribed in Factory & Machinery Act 1967. I. Factory & Machinery…

Q: Hazardous waste is waste that poses substantial or potential threats to public health or the…

A: Correct answer: C ) I,II, III, IV

Q: Q5. the acceleration due the gravity on the moon is 1/6 of what it is on earth. If you can throw a…

Q: In the ideal Rankine cycle shown, the boiler pressure is 6 MPa and the condenser pressure is 8 kPa.…

Q: The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5…

A: For the given universal joint it is required to determine: 2.1 tensile stress in each rod 2.2 shear…

Q: Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside…

A: Find the velocity at point D.

Q: Q2. An object moves from rest in a straight path with acceleration 2 m/s² until it travels a…

Q: To investigate the effect of force orientation on the velocity of a collar, following experiment has…

Q: DESCRIBE WHAT HAPPENS TO FLUID AS IT FLOWS THROUGH A COMPRESSOR SPECIFICALLY HOW YOU WOULD YOU…

Q: The internal pressure p of the cylindrical pressure tube seen in Figure 4, whose radius to wall…

Q: A small turbine runs an aircraft refrigeration system. Air enters the turbine, at 4 bar and 40°C…

A: In this case, we know that an aircraft refrigeration system is powered by a tiny turbine.At 4 bar…

Q: A concentric helical spring is used to support a load of 90 KN. The inner spring has a rate of 495.8…

A: Find the percent load carried by the inner spring.

Q: he 3770-lb car is traveling at 26 mi/hr when the driver applies the brakes, and the car continues to…

Q: Attitude, environment, and system are a factor in the workplace that influence by a safety culture.…

A: For the safety culture model:- An Organizational atm. where S & H are understood and is…

Q: If a certain gas has Cp of 1.005 kJ/kg-K and Cv of 0.678 kJ/kg-K, determine the value of k, T2,…

A: Given data cP =1.005 kJ/kgKcV = 0.678 kJ/kgKP1 = 101.325 kPaT1 = 77°C1-2 : Adiabatic Compression…

Q: As shown in the following figure, a slider moves through the guide from point A to point E and then…

Q: 1-74. Member B is subjected to a compressive force of 3 kN. If A and B are both made of wood and are…

Q: The rod OA rotates in the horizontal plane such that e= 0.72t radian, and collar B is sliding…

Q: 2. Three bars, hinged at A and D and pinned at B and C as shown in Figure 1-60, form a four- link…

A: Given Force, F = 20 kN Angle = 45o Find Another force, P

Q: Consider (Figure 1). For a short period of time, the motor turns gear A with a constant angular…

A: Jskak

Q: c. Find the homologous temperature (or the percent homologous) of Material A with a melting point of…

A: Given

Q: The range R, or the maximum horizontal distance, of a projectile on level ground launched at an…

Q: A body weighing 2,225N is being dragged along a rough horizontal plane by a pull of 445N directed at…

Q: If the 50 mm radius motor pulley A of the clothes dryer rotates with an angular acceleration of…

A: Find angular velocity when t = 3 sec.

Q: A 1-m³ rigid tank contains air at 35°C and 125 kPa at a relative humidity of 45%. Determine the…

A: (a) The partial pressure of dry air is 122.467 kPa. (b) The enthalpy per unit mass is 68.185 kJ/kg…

Q: Column A Column B Increasing thickness of alumina Hardness Column A Column B Increase in atomic…

A: 1) increase in thickness of the lamina DECREASE the hardness. 2)Increase in atomic packing factor…

Q: There are many types of traffic control system for the lift system. Give a short account on the…

A: Write a short account on the following three control systems. (1) Down collective control.(2)…

Q: Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside…

A: Find the simplified bernoulli's equation for the point A and D.

Q: mm. If in both cases t is in seconds, determine the magnitude of velocity (mm/s) of the collar when…

A: The magnitude of velocity of the collar: V = 464.742 mm/sec

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

A motor is driving a solid circular steel shaft transmits
40kW of power at 500 rpm. If the diameter of the shaft is
40 mm, The maximum shear stress in the shaft is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A hollow shaft for a rotary compressor is to be designed to transmit a maximum of torque of 4750 N-m. The shear stress in shaft, if the ratio of the inside to the outside diameter is 0.4
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
find the maximum shear stress induced in a solid circular shaft of diameter 150 mm when the shaft transmits 150 KW power at 150 RPM.