Example Problem 1 A U-shaped pipe with uniform circular cross section of area A is half submerged in a tank of water and is traveling left a velocity of V. As the pipe scoops up water from the tank it is ejected to the left out of the pipe. Compute the force necessary to keep the pipe moving at the constant velocity V. Given: V = 1.5 m/s A = 0.0026 m^3 Patm = 100kPa Rho = 1000 kg/m^3

Example Problem 1 A U-shaped pipe with uniform circular cross section of area A is half submerged in a tank of water and is traveling left a velocity of V. As the pipe scoops up water from the tank it is ejected to the left out of the pipe. Compute the force necessary to keep the pipe moving at the constant velocity V. Given: V = 1.5 m/s A = 0.0026 m^3 Patm = 100kPa Rho = 1000 kg/m^3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A jet issues without loss from a hole in a water tank that is open to the atmosphere. The hole is located a distance H below the free surface, and the jet issues at an angle θ to the horizontal direction, and it has an exit area of A. Express the maximum height of the jet as a function of θ and H (which is held constant). What is the the horizontal component of the force exerted on the tank by the jet? Ignore losses.
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degreesupwards. The water velocity and corresponding pressure at the inlet to the band is 4, 5 m/s and 70 kParespectively. Determine the weight flow, the water flow velocity at the exit to the bend, the bend exitpressure if the friction head loss through the bend section is 2 m and the magnitude and direction ofthe resultant force flowing through the bend.
A hemispherical tank of diameter 4 m contains water up to a height of 2.0 m. An orifice of diameter 50 mm is provided at the bottom. Find the time required by water (i) to fall from 2.0 m to 1.0 m (ii) for completely emptying the tank. Take Cd= 0.6
A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
A large internal-combustion engine takes in air at 2 kg/ s and fuel of relative density0·85 at 8·8 L/ min. The exhaust pipe has a diameter of 400 mm and the exhaust gashas a density of 0·4 kg/m3• Assuming steady-flow conditions, calculate the velocity ofthe exhaust gas.
The water enters the sprinkler nozzles with a flow rate of 50 liters / hour in the vertical axis direction and leaves the sprinkler nozzles as 25mm diameter jets and making θ angle with the tangential direction as shown in the figure. The length of the sprinkler arms is 0.45 m. Without considering friction effects; For θ = 75 °, set the rotational speed in rpm.
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
Water flows from a large tank through an orifice of 75 mm diameter and against a block as shown in the figure. The water jet strikes the block at the vena contrata. The block weighs 223 N and the coefficient of friction between the block and the floor is 0.57. The coefficient of discharge C = 0.60 and its coefficient of contraction Cc = 0.62. What is the minimum height to which water must rise in the tank in order to start the block moving to the right?
Consider steady developing laminar flow of water in a constant-diameter horizontal discharge pipe attached to a tank. The fluid enters the pipe with nearly uniform velocity V and pressure P1. The velocity profile becomes parabolic after a certain distance with a momentum correction factor of 2 while the pressure drops to P2. Obtain a relation for the horizontal force acting on the bolts that hold the pipe attached to the tank.
A vertical pipe of 1 m diameter and 20 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.6 m of oil. The density of oil is 880 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) upward direction, (b) downward and also draw the neat sketch. i) Pressure at lower end when flow of oil is upward =________________ N/m2 ii) Pressure at lower end when flow of oil is downward =________________ N/m2
A 300-mm pipe carries oil of sp gr 0.812 at a rate of 0.111 m /s, and the pressure at point A is 18.4 kPa gage. If point A is 1.89 m above the datum plane, calculate the energy at A.