Barrel elevating w/ respect to turret at -2rad/s J with angular acceleration +10 rad/s² Ĵ. Turret is training w/ respect to the ground at +1 rad /s and angular alleleration of +4 rad/s 2 k. Barrel IS slender rod. K turvet 2 O barrel 2m 20kg What are the reaction forms developed at the connection between barrel and turret?

Barrel elevating w/ respect to turret at -2rad/s J with angular acceleration +10 rad/s² Ĵ. Turret is training w/ respect to the ground at +1 rad /s and angular alleleration of +4 rad/s 2 k. Barrel IS slender rod. K turvet 2 O barrel 2m 20kg What are the reaction forms developed at the connection between barrel and turret?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please help me with the following question. please put the whole process and solution because I’m having a difficulty with understanding it. Thank you very much. Determine the reactions at the following: A (Normal) - B (Horizontal ) - B (Vertical) - FN=78MN=104SN=66
plzzzz help me nowww What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
force@ D=40kips. I have provided the reactions. Pls continue Asap. Thanks
Compute the load that will compress the combined bar a total of 0.8mm in the lenght of 2m. If the bar is 2m long and surrounded by a cast iron 5mm thick and a bar radius drived from a bar design that can hold 3 liters of liquid with the minimum amount of materials to be used for construction. For steel, E=200 Gpa, and for cast iron, E= 100 Gpa. Prove that the parameters are minimum value.
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1179.9 Nm, U = 4330 Nm, x = 3.03 m, y = 2.25 m, z = 1.34 m, d = 94 mm, and e = 76 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places.
Table of values: bf = 1482 mmbw 462 mmt = 292 mm fc' = 28.2 MPafy = 384 MPad = 1011 mmd' = 112 mmL(beam) = 15.1 mW_D1= 48.4 kN/mW_L1 = 56.9 kN/mW_D2 = 184.4 kN/mW_L2 = 208.9 kN/mPROBLEM: A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (W_D1, W_L1)and pair 2 (W_D2, W_L2). The geometric, material and loading properties are all given on thetable above. 1. Solve for the height of the compression stress block using pair 1. 2. Solve for the theoretical steel area using pair 1. 3. Using Es = 0.004, solve for the theoretical steel area using pair 2. 4. Using Es = 0.005, solve for the theoretical steel area using pair 2.
A steel column carries an axial load of 819 kN and a moment of 63 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13172 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Compressive Stress if Axial load only existed.
Calculate reaction at A and B point -
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
A beam 300mm x 600mm has a steel area of 3321mm2 at the bottom with steel covering of 75mm. Use: f’c = 28 MPa Es = 200,000 MPafy = 276 MPa Ec = 4700 √f’cfr = .70 √f’ca) Determine the effective moment of inertia of the beam which carries a dead load of 10KN/m (including its own weight) and a concentrated live load of 100 KN acting at the center of the 6 m simple span.b) Determine the instantaneous deflection of the beam.c) Determine the long-term deflection if 20% of the live load will be sustained after 1 year.
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?
A steel column carries an axial load of 808 kN and a moment of 76 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 13080 mm2 rx = 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Allowable Compressive Stress.