at Cand subjected load P as shown. The solid shaft is fixed to the support to the torsional loadings and axial a) Determine the torsional shear stress at Point A (50 mm from the center) and b) Point B (on the surface) a) b) Determine the absolute maximum torsional shear stress in the shaft. c) Sketch the state of stress at point A and draw its corresponding Mohr's Circle of Stress. Compute the principal stresses and maximum in-plane stress. rt C 50 mm TKN-m 75 mm BR 4 kN-m O 75 mm P= 20 kN 4

at Cand subjected load P as shown. The solid shaft is fixed to the support to the torsional loadings and axial a) Determine the torsional shear stress at Point A (50 mm from the center) and b) Point B (on the surface) a) b) Determine the absolute maximum torsional shear stress in the shaft. c) Sketch the state of stress at point A and draw its corresponding Mohr's Circle of Stress. Compute the principal stresses and maximum in-plane stress. rt C 50 mm TKN-m 75 mm BR 4 kN-m O 75 mm P= 20 kN 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-sectional is square, 0.55 in. On each side.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
A thin walled tube of thickness (t) 5mm and diameter (d) 200mm with closed ends is subjected to an internal pressure (p) 7.0 MN/m2, producing an axial and circumferential direct stresses given by pd/4t and pd/2t respectively. A torque T = 15.0 kNm is also applied which sets up a shear stress ? = ?/2??2? where r is the radius. (a) Determine the magnitude and direction of the principal stresses. (b) Calculate the overall maximum shear stress.
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-section is square, 0.45 in. on each side. Draw free-body diagram.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
A. Determine the maximum bearing stress in MPa if P = 115 kN. B. Determine the maximum shear stress in MPa if P = 115kN. C. Determine the maximum tensile stress in MPa if P = 11 kN.
e. unit horizontal shearing stress at the base in kPa
Determine the magnitude of the maximum vertical force P (in kN) that can be applied to the bell crank so that the average normal stress developed in the 10-mm diameter rod CD, and the average shear stress developed in the 6-mm diameter double sheared pin B not exceed 175 MPa and 75 MPa, respectively
if the shaft is subjected to ana axial force of 5 kN. determine the bearing stress acting on the collar A. Determine the average shear stress developed on the shear plane on collar A
For the state of stress shown in the figure. a. Determine the maximum and minimum principal stresses.b. Describe the location of the maximum principal stress from side BC.c. Describe the location of the maximum principal stress from side BD.d. Determine the maximum shear stress.e. Determine the normal and shear stresses at plane AB. A = 30 ,B = 50 , C = 10 ,D = 37
Determine the maximum shear stress developed in the 44 mm diameter shaft.
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B