Member AB is supported at B by a cable and at A by a smooth square rod that slides into the hole in the collar. Determine the tension in cable BC and the components of the reaction at A when P = 300 N.

Q: Determine the reactions at supports A and B. 4 kN A 30° 6 m 2m

A:

Q: Determine the reactions at the supports at A and C. Also, obtain the force exerted by the pin at B…

A:

Q: Determine the tension in cable BE .and the reactions at A and D

A: W = 80 kN Find the tension and reaction at A and D

Q: Q3) Determine the maximum weight of block A for which the maximum tension in cable CD does not…

A: Given Data TCD=160 N

Q: 1) A mass of 100 kg is applied on the 50 kg uniform beam at point C as shown. If the pulley at D is…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: Determine the tension in each cable and the components of reaction at D needed to support the load.…

A:

Q: Beam AD carries the two 40-lb loads shown. The beam is held by a fixed support at D and by the cable…

A: Draw the free body diagram of the beam and the weight saperately: From the free body diagram of the…

Q: DETERMINE THE REACTION AT A AND E, AND THE FORCES ACTING ON ALL MEMBERS. DETERMINE THE WHETHER THE…

A:

Q: The 40-ft boom AB weighs 2 kips; the distance from axle A to the center of gravity G of the boom is…

A: Free Body Diagram:

Q: Collars A and B are connected by a 25-in.-long wire and can slide freely on frictionless rods. If a…

A: (a) The free-body diagram of collar A, The co-ordinates for point A, The co-ordinates for point B,…

Q: Q3) Determine the tension developed in wires CA and AB required for equilibrium of the 51.5 N block.…

A:

Q: Q6\ If the tension in the spring is 600, the vertical component of the pin reaction at B is:

A: Consider the free body diagram of the EB and AC as shown below.

Q: Two transmission belts pass over pulleys welded to a shaft which is supported by bearings at B and…

A: The radius of the pulley at A is RA=2.5 in. The radius of the pulley at C is RC=2 in.

Q: urgent please 2 hour please please hand written please

A: Given data: F=350 N Need to determine the tension in each cable.

Q: Q3) Determine the maximum weight of block A for which the maximum tension in cable CD does not…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: The 240-lb uniform tank is suspended by means of a 6.5-ft-long cable, which is attached to the sides…

A:

Q: 3. The horizontal force P= 150 N is applied to the handle of the puller. Determine the resulting…

A: Problem (3): Given: The horizontally applied force at the handle of the puller is P=150 N. The…

Q: a) Determine the reactions at A and E b) Determine the forces in members CD, CF, and GF using the…

A: The free-body diagram of the truss is shown below,   tanθ=45θ=tan-145θ=38.66° Now balancing the…

Q: The rig shown consists of a 1200-lb horizontal member ABC and a vertical member DBE welded together…

A:

Q: The 40-kg homogeneous plate is suspended from four wires. Determine the tension in wire D.

A:

Q: Q2: - The weight W= 10 kN hangs from the cable, which passes over the pulley at F. Neglecting the…

A:

Q: Q3) Determine the maximum weight of block A for which the maximum tension in cable CD does not…

A: Given data: Maximum possible tension in CD (TCD) = 160 N Need to determine the weight of the block…

Q: 2. The weight W=6 kN hangs from the cable which passes over the pulley at F. Neglecting the weights…

A:

Q: Q2/ (a) Draw the free-body diagram of the beam. (b) Determine the tension in the rope and the…

A: (a) The free body diagram of the beam is as follows: (b) Calculate the moment about point B as…

Q: Q (3): Determine the tension in AC and BC if two cables are tied together at C and loaded which has…

A: m=18 kg

Q: 5. Determine the tension developed in cable AD to have the tower in equilibrium if the tension in…

A: Find the position vector of points  A, B, C and D: rA=30 k^rB=10 i^-15 j^rC=-15 i^-10 j^rD=12.5 j^…

Q: 2.The lever BCD is hinged at C and is attached to a control rod at B. If P = 200 N, determine (a)…

A: Given- Data:- Load(P)=200N To-Find:- a) Tension in the rod AB b) The reaction at C

Q: Determine the horizontal reaction at support A when the value of F=30lb and G=75lb. – 2 ft-2 ft - B…

A:

Q: The uniform plank ABC weighs 400 N. It is supported by a pin at A and a cable that runs around the…

A: Consider the free body diagram of the given system.

Q: 1) The jib crane is pin-connected at A and supported by a smooth collar B. Determine the reaction…

A: Given data: The magnitude of the load P is P = 122 N. The distance between AB is H = 12 m. The…

Q: The 40-ft boom AB weighs 2 kips; the distance from the axle A to the center of gravity G of the boom…

A: Boom length = 40 lb Weight of AB = 2 kips The distance of CG G of the boom AG =20 ft. Determine, A.…

Q: Determine the tension in the horizontal cable

A: Given data as per the question weight =200 kg Considering the fig. and forces applied to it…

Q: 1. For the frame shown, determine the reaction at E assuming a pinned support. The tension in the…

A:

Q: Determine the tension in the cable and the components of the reactions of the bolt at A, considering…

A: Solution: Given Data: W = 80 lb

Q: 1. Determine the four reactions at the journal bearing A. 2. Determine the tension in cords BC and…

A:

Q: Q2: Determine the reactions of fixed support at A 15 kN 15 kN 8 KN/m 4 kN/m B 3 m 3 m

A:

Q: A crate of 30 kg hangs as shown. Fixed support at A. If the cable BC has a tension of 20 N determine…

A:

Q: Determine the reactions at pin A and the tension at cable BC. |30 kN (a)

A:

Q: Member AB is supported by cable BC and at A by a square rod which fits loosely through the square…

A: Data given-  W = 800 N  a = 0.2 m  b = 0.6 m  c = 0.3 m

Q: The pin, attached to member BCD, passes through a smooth slot in member AB Take w = 120 lb/ft.…

A:

Q: Bar AD is attached at A and C to collars that can move freely on the rods shown. If the cord BE is…

A: Let the tension in cord is T, load in point D is 80 N, and RA & RC is a reaction force from…

Q: Determine the tension in cables BC in N necessary to support the 71-kg cylinder if the tension in…

A:

Q: 5 KN Determine the reactions at A and the tension in the cable connected to B. Neglect the weight of…

A: Given:- To Find:- Tension in the cable connected to B. (TB)  Reactions at the point A.

Q: If the tension in the cable BC is 100 lb, determine the reactions at the fixed (cantilevered)…

A: The free-body diagram showing reaction at support is as follows,

Q: The pipe assembly supports the vertical loads as shown. Determine the components of reaction at the…

A:

Q: Neglecting friction, determine the tension in cable ABD and the reaction at C w hen 0=60°.

A: Equilibrium moment about the point C is.…

Q: 4. Determine the reaction at support A of the pipe system shown below, when the force applied at the…

A:

Q: Q.2 Determine the reactions at the supports. 4 kN 3 m B +2 m- 3m 1 m

A:

Q: 4. If cable CB is subjected to a tension that is twice that of cable CA, determine the angle e for…

A: Given data Mass of cylinder = 10kg

Q: 15 kN/m Q2/ Determine the reactions at roller (A) and pin (C) for equilibrium of the member (ABC),…

A: