Member AB is supported by a cable BC and at A by asquare rod which fits loosely through the square hole in thecollar fixed to the member as shown. Determine thecomponents of reaction at A and the tension in the cableneeded to hold the rod in equilibrium.3 m6 m400 NC300 Nx 2 mBF: Applied force=FF: Reaction force at A=F(A);components are A(x), A(y), A(z)T : Tension force in cable BC=T(BC)ignore weight of the member AB.What is the y component of the reaction force at A? 35-O A) Aly)=600 NewtonB) A(y)=1200 NewtonC) Aly)=1500 NewtonD) Aly)=300 NewtonO E) Aly)=900 Newton

Answered: Image /qna-images/answer/72160f42-c221-4efd-85cc-3c3fa61f797c.jpg

Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member as shown. Determine the components of reaction at A and the tension in the cable needed to hold the rod in equilibrium.

Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member as shown. Determine the components of reaction at A and the tension in the cable needed to hold the rod in equilibrium.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A two-dimensional beam structure or frame (ABCD, shown below) has a concentrated load, P, acting on Point D. You can assume that the connections at B and C have sufficient strength to react the applied load and that loads and moments are transferred between the beams. You can assume that the members have a constant cross-section and that El-constant. B A 2m y L. C P-3kN D 2m In order to evaluate the design you must: (a) Sketch the deformed shape of the frame, solve the reaction forces and construct the bending moment diagram for the frame. (b) Use any method to determine the vertical deflection at Point D. Ensure that you clearly explain your approach and show your final answer. Clearly state any assumptions made. (c) If the bending rigidity, El, of the frame between Point B and Point C was doubled. What effect would this have on the resulting horizontal deflection at point D. Ensure that your answer is supported by suitable reasoning, calculations and/or sketches.
The A-36 steel rod has a diameter of 50 mm and is firmly attached to the rigid supports at A and B when the initial temperature is 50°C. Determine the force P in kN that must be applied to the collar at its midpoint so that, when the final temperature becomes 30°C, the reaction at B is zero. Where: a=12x10^6 m/(m°C), E = 200 GPa and L = 500 mm A B L
The A-36 steel rod has a diameter of 50 mm and is firmly attached to the rigid supports at A and B when the initial temperature is 50°C. Determine the force P in kN that must be applied to the collar at its midpoint so that, when the final temperature becomes 30°C, the reaction at B is zero. Where: α=12x10^6 m/(m°C), E = 200 GPa and L = 500 mm
Aen = a0 © @2 Z Q23-7-2018p.. Q1: A railway ridge consisting of truss construction as shown in the Figure below, this truss is supported by A and B. The forces on joints il and V are i the uss result from a i crossing the railway bridge Determine the following: (a)the reactions forces in A and B (b)the forces of the truss members in joints (1.1, I and 1V) >
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm
Rigid bar ABC is supported by two identical solid bronze [E - 96 GPa, a = 18.2 x 10-6/°C] rods, and a solid steel [E - 210 GPa, a = 9.9 × 10-6/°C] rod. The bronze rods (1) each have a diameter of 16 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 27 mm. The bars are unstressed when the structure is assembled at 22°C. Assume L = 0.3 m. When the temperature decreases to -15°C, determine: (a) the normal stresses in the bronze and steel rods o1,02 (positive if tensile, negative if compressive). (b) the normal strains in the bronze and steel rods e1, €2 (positive if stretched, negative if shortened). (1) (1) L Answers: i MPa, 02 = i MPa. i HE, E2 = i με. = I3
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and E,= 100 GPa, determine (a) the reactions at A and E, (b) the stress at segment BC, (c) the deflection of point D. Dimensions in mm 100 100 -180- -120- A Cl Dl E Steel B Brass 60 kN 40 kN 40-mm diam. 30-mm diam.
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 520 mm². Bar (2) is an aluminum alloy [E = 77 GPa] with a cross-sectional area of A₂ = 380 mm². A concentrated load of P = 58 kN acts on the structure at D. Assume L₁=730 mm., L₂=440 mm., a=680 mm., b=420 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 0₂ in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) 6₁ = (b) VD= i L₁ L2 (2) B с MPa, 0₂ = mm. D P MPa
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 116 GPa] with a cross-sectional area of A₁ = 550 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 290 mm². A concentrated load of P = 62 kN acts on the structure at D. Assume L₁=800 mm., L2=560 mm., a-590 mm., b=430 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) σ₁ = (b) VD = i (1) L₁ L2 (2) A B MPa, 0₂ = mm. D MPa
For the beam and loading shown, determine the reaction at the roller support. Assume that the flexural rigidity El of the beam is constant. (Round the final answer to two decimal places.) Given: w2wo A -L- { x = 0, y = 0} { x = 0, y = 0} {x=L, y = 0} The reaction at the roller support is 0.37 wo Lt. B
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A₁ = 630 mm². Bar (2) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₂ = 340 mm². A concentrated load of P = 52 kN acts on the structure at D. Assume L₁=910 mm., L₂=430 mm., a=450 mm., b=280 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a 5 Answers: (a) 6₁ (b) VD= = tel i (1) L₁ L2 B C MPa, 0₂ = mm. i MPa