Member AC shown in Figure SM-211 is subjected to a vertical force of 3 kN. The rod AB has a cross-sectional area of 400 mm² and the contact area at C is 650 mm². Determine the stress in rod AB if x = 100 mm. 3 AN Select one: O a. 3.75 MPa O b. 2.5 MPa O c. 2 MPa O d. 3 MPa 200 mm Figure SM-211

Member AC shown in Figure SM-211 is subjected to a vertical force of 3 kN. The rod AB has a cross-sectional area of 400 mm² and the contact area at C is 650 mm². Determine the stress in rod AB if x = 100 mm. 3 AN Select one: O a. 3.75 MPa O b. 2.5 MPa O c. 2 MPa O d. 3 MPa 200 mm Figure SM-211

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A pipe of Aluminum alloy is subjected to a tensile force F along its longitudinal axis. The pipe has…

A: According to hook's law young modulus E = stress / strain(recoverable) Here given E = 75 Gpa = 75 x…

Q: Determine the following: a. Flexural rigidity of the beam in kN-m². b. Slope at the ends and…

Q: Analyse rame adors on method.

A: Since you have posted a question with multiple sub-parts, we will solve first 3 sub parts for you.…

Q: SITUATION. The cable of a suspension bridge shown in the figure below runs over a frictionless…

Q: Problem I. Solve the problem using Conjugate Beam Method. Given the figure, determine the following…

Q: Calculate Joint Strength of 5.5 inch, 23 lb/ft, N-80 grade casing, and maximum length of casing (in…

A: Given, D = 5.5 in Ultimate strength (σu) = 80 ksi

Q: Q2: A five-sided field traverse has the following balanced angles: A = 101°28′26"; B=102°10'42"; C =…

A: Part B Bearing of EA= N20°20'20''W = 339°39'40'' AE= 159°39'40''= S 20°20'20''E…

Q: please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound…

A: Given data: T=1179.9 NmU=4330 Nmx=3.03 my=2.25 mz=1.34 md=94 mme=76 mmCBr=35 GPaCst=83 GPaCal=28 GPa

Q: Given the built-up beam shown 10' simple span beam W = 3000 lbs/ft Determine the maximum shear…

A: Given :

Q: 10 ft- A -10 ft. C -10 ft- B -5 ft-

Q: 11. What will be the shearing resistance of a sample of clay in an unconfined compression test,…

Q: EQ-2: A) Use LRFD method and design the sag rods AB or CD shown for the service live load of 30kips…

Q: Use the area-moment theorems to determine the smallest moment of inertia I required for the beam…

Q: A compression member with an effective length of KL = 12 ft is built up from a W shape and a…

Q: power (in kW) recovered in the turbine

A: Given:' Density of water= 9810 N/m3 = 1000.34 kg/m3 g = 10 m/s2 Efficiency of turbine and pump = 70%…

Q: Pressure exerted on a block of wood present at a depth of 30 m under water?

A: Given:Depth, d=30 m

Q: Q2 / Abuilding to be constructed on a hill with foundation elavation = 30m. the areas bounded by…

A: The given data is shown below:

Q: Explain the difference between symmetric bending and general bending theories of beams.

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: Porosit, n = 0.3 Hydraulic conductivity, K = 1 m/day protected wetlands D. 5 h=90m с El water table…

A: Given data: Porosity(n)=0.3 Hydraulic conductivity(k)=1 m/day No.of flow lines=4 No.of potential…

Q: Sieve size (mm) 10 5 2.36 1.18 0.6 0.3 0.15 0.075 Wt. retained 0 7 30 33 62 98 55 18 Retained (%)…

Q: 35 kN/m -5m 1600 (10) mm E B 150 kN Hinge -2.5m-2.5 m- 1200 (10) mm E-constant-210 GPa D

Q: . A single ISA 100 x 75 x 10 is used as a tension member with the longer leg connected to a 10 mm t…

A: given :

Q: Q4: The bearings and lengths of straights R1-X1 and X1-R4 taken from Table below, are as follows:…

Q: Problem #1 E Cft Loca The street-lights at A and B are suspended from the two poles as shown. If…

Q: Q4/ The solid shown consists of a cone of radius (r) and height (h₁) and a cylinder of radius (r)…

Q: 4. Investigate the adequacy of the beam reinforced for tension and compression as shown. The total…

Q: 5. Using the derived equation from the previous question, solve the following problem: A race car is…

A: Given, r = 55 m θ = 40o S = 216 km/hr or 60 m/s

Q: The sequent depth ratio of a hydraulic jump in a rectangular channel is 12. What would be the…

A: Given data- Sequent depth ratio-y2y1=12where,y2=post jump depthy1=pre jump depthTo Find-The…

Q: Problem 2: The grains of wood in the bar make an angle of 20° with the horizontal as shown.…

Q: For the given moment diagram, draw the load and shear diagram. All curves are 2°. 72 in. 48 in. 5000…

Q: SITUATION. The cable of a suspension bridge shown in the figure below runs over a frictionless…

A: Given that :

Q: The beam ABC is to be loaded with a 300 lb/ft uniform distributed live load so it causes the largest…

Q: 5. A single ISA 100 x 75 x 10 is used as a tension member with the longer leg connected to a 10 mm…

Q: 3 Consider a horizontal 4-ft-diameter galvanized-iron pipe simulating the Alaska Pipeline. The oil…

A: Given that :

Q: Q.1 The velocity distribution in a turbulent boundary layer is given by 1/7 -(0)" 52

Q: ortions of the rod ABC are made of an aluminum for which E = 69GPa. Knowing that the magnitude of Q…

A: For zero defelction :δAB=δBC

Q: 38. The wagon wheel has a diameter of 28 inches and an angle of 30° between the spokes. What is the…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: A reinforced concrete column 500 mm × 500 mm in a section is reinforced with 4 steel bars of 25 mm…

A: E for steel = 210×10^3N/mm2 E for concrete = 14×10^3 N/mm2 Steel bars = 4 dia = 25mm Column load=…

Q: A uniform thin bar, 1.8 m long and weighing 50 kg, slides along the wall and smooth floor shown in…

A: Given data m = 50 kg l = 1.8 m tg= 4/3 acc. at A = 3 m/s2 we have to Calculate the force P that…

Q: Select a 30-ft-long W12 section of A992 steel to support a tensile service dead load PD = 130 k and…

A: As per AISC LRFD Specification The strength in design φt Pn is the taken as minimum of the…

Q: 4. Please discuss the Poisson's ratio of concrete in terms of compressive strength. Is there an…

A: Poisson's ratio is defined as ratio of transverse strain to the ratio of longitudinal strain .…

Q: Notes: Attempt Five Question only Q1: For the composite structure shown in Fig.(1), determine the…

A: Composite structures are commonly known as Load-bearing elements which consist of elements like…

Q: In its natural condition, a soil sample has a mass of 1.980 kg and a volume of 0.001 m³. After being…

Q: 16. A student was asked to make a 345.43-m long line using a 25-m tape that is 0.0021 m too long.…

A: Please all given questions we are told to solve only question number 16 to question number 18 Please…

Q: PROBLEM 2: A stone is thrown upward from the ground with a velocity of 15 m/sec. One second later…

Q: The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the…

A: Disclaimer Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The beam shown has a constant El and is supported as shown. Find the following: 300 15 kN/m a.…

A: Conjugate beam method - Let us divide it into parts and solve RA +RB'=300…

Q: Question 9: Determine the vertical and horizontal components of force acting on radial gate ABC in…

Q: C. Calculate the modulus of elastisity for a material which produces the following data when…

Q: A-Figure (1) shown the dividing a tract of land into two parts by a line between two Given the data…

A: Lattitude is measured in N-S direction Departure is measured in E-W direction Lets take A as…

Concept explainers

Introduction to Architectural Drafting

Architectural drafting converts vision and ideas into technical drawings and detailed plans for the construction of buildings, such as institutional, residential, and commercial buildings. It helps engineers and architects to outline the working data and details, such as structure type, codes, elements, and kind of materials.

Question

SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION

Member AC shown in Figure SM-211 is subjected to a vertical force of 3 kN. The rod AB has a
cross-sectional area of 400 mm² and the contact area at C is 650 mm². Determine the stress
in rod AB if x = 100 mm.
JIN
Select one:
O a. 3.75 MPa
O b. 2.5 MPa
O c. 2 MPa
O d. 3 MPa
201
Figure SM-211

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the point given the plane stress state, which of the following is the correct type and limit values of Mohr Circle? sx =-40 MPa (Bası), sy =60 MPa (Çeki) txy =60MPa
An aerial copper wire (E = 1 × 10^5 N/mm^2) 40m long has cross sectional area of 80 mm^2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculate: a. the elongation of wire due to self-weight. b. the total elongation when a weight of 200N is attached to its lower end. c. the maximum weight which this wire can support at its lower end if the limiting value of stress is 65 x 10^5 N/mm^2 I need answer ASAP. Thank you!
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 0.9 GPa. Each bar has a cross-sectional area of 1050 mm2. Using L = 395 mm and Δ = 7.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? [Answer: P = 67.0 kN]
A hollow circular bar of cylindrical steel is 1.5 m long and has inner and outer diameters of 40 and 60 mm. (a) What is the largest torque I can apply to the circular bar if the shear stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shear stress in the circular bar? (answers: (a) 4084.1 N.m (b) 2722.7 N.m)
When an axial load is applied to the ends of the two-segment rod shown in Figure P2.1, the total elongation between joints A and C is 7.5 mm. The segment lengths are a = 1.2 m and b = 2.8 m. In segment (2), the normal strain is measured as 2,075 um/m. Determine:(a) the elongation of segment (2).(b) the normal strain in segment (1) of the rod. (Ans. to check: Normal strain (1) = 825uE
A solid 1.40-in.-diameter steel [G = 12,000 ksi] shaft is subjected to the torques shown. Determine the magnitude of the maximum shear stress in shaft segment (1). a 1.82 ksi b 2.45 ksi c 3.86 ksi d 3.01 ksi e 2.85 ksi
Topic: Strema A 750-mm high cylinder carries a load P which produces a normal stress at its cross-sectional area and a shear stress at its lateral surface area. Find its diameter if these stresses are equal. Choices: A. 3.0 m B. 4.5 m C. 1.5 m D. 6.0 m
Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. Aluminum rod (1) has a diameter of 10 mm and a cross-sectional area of A1 = 78.54 mm2. The stress in rod (1) may not exceed 170 MPa. Bronze rod (2) has a diameter of 13 mm and a cross-sectional area of A2 = 132.73 mm2. The stress in rod (2) may not exceed 110 MPa. Assume that L = 1900 mm and a = 900 mm. Determine the largest load magnitude P (in kN rounded to the nearest tenths) that may be applied to rigid bar BC.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitude acting on horizontal and veritcal planes at the point are Sx= 12.7 ksi, Sy= 1.7 ksi, Sxy= 5.8 ksi. Assume beta= 34 degrees. Determine the normal stresses and shear stress
For the beam shown, determine the support reactions and draw the stress diagrams. shear and bending moment. EI is constant. The rigth answer is: VA = 1.3 kN (↑); HA = 0 kN; MA = 4.40 kN.m (clockwise); VB = 51.20 kN (↑). I don't know how to get these results, please show how, step by step.
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3 cm and internal diameter 2.3 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis (i) The moment of inertia in (mm^4)= ii) The radius of curvature in (mm) = (iii) The maximum bending stress in (N/mm^2)= iv) The bending stress at the point 0.6 cm from the neutral axis in (N/mm^2)=