The members of the structure in Fig. 1 weight 150 lb/ft. Determine the smallest diameter pin that can be used at C if the shearing stress is limited to 4000 psi. Assume single shear Q2/ The members of the structure in Fig. 1 weight 150 lb/ft. Determine the smallestdiameter pin that can be used at C if the shearing stress is limited to 4000 psi. Assumesingle shear.40 kN6 ft2 ftC4 ft - 3 ft

Length of AB=42+42 =5.656ftConcentrated load (WAB)=150×5.656=848.528 lb…

Answered: The members of the structure in Fig. 1…

The members of the structure in Fig. 1 weight 150 lb/ft. Determine the smallest diameter pin that can be used at C if the shearing stress is limited to 4000 psi. Assume single shear

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Related questions

Q: 2. The 7/8 in diameter pins at A and C that support the structure are in single shear shown in…

Q: Determine the reactions at supports A and B due to the applied loads shown

Q: Determine the maximum shear (k) at the given structure. 10 k 0.8 k/ft 8k IC 6 ft- 12 ft- 12 ft- 6 ft

Q: Question 1 Determine the maximum negative shear at E (in kN) due to dead load of 3 kN/m and the two…

Q: 1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum…

Q: Problem 4.1. The two-member pinned frame is subjected to the distributed loading shown. Member CB…

A: At a point in a section, stress is also known as force per unit area. Forces per unit area that act…

Q: Determine the maximum shear (kN) in the given structure.

Q: A bar ABCD of circular cross section having a diameter of 50 mm is firmly supported at each end and…

A: Given data: Diameter D = 50 mm Torque at B = 1000 N m Torque at C = 1500 N m Length of AB (LAB)= 2 m…

Q: 50 kN В -2 m 4 m

Q: The horizontal rigid beam ABC is supported by vertical bar BD and is loaded by a force P acting at…

Q: Q1. Figure Q1 shows a steel member imposed with various loadings supported by a roller and pin at A…

A: The diagram is shown below, Tanθ=43Sinθ=45Cosθ=35

Q: draw the FBD of member AB, compute for the shear ordinates and draw the Shear Diagram

Q: Q-2 The continuous beam ABC, Fig.2, is of two equal spans L. Pad is loaded with two equal…

A: Method of Consistent Deformation : The method of consistent deformation is also known as force…

Q: For the pin-connected structure, determine the minimum diameter for the pin at joint D if the…

A: Let us draw the FBD of the frame for our analysis

Q: Question 1 Determine the maximum negative shear at E (in kN) due to dead load of 3 kN/m and the two…

Q: 1.38 The right-angle bar is supported by a pin at B and a roller at C. What is the maximum safe…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. FAH 2 m 25KN FAV What is…

Q: Problem Five: Joint B is a pinned joint in single shear. The pin at B has a diameter of 0.5 inches.…

A: The free body diagram of beam BC is shown below. Consider the equilibrium of forces in vertical…

Q: 4. Determine the reactions and draw the shear and bending moment diagrams for the beam shown using…

Q: Q2: For the structures and loadings shown 4m Draw the normal and shear force diagram. Draw the…

Q: d. Determine and plot the shear diagram for the given loading conditions. e. Determine and plot the…

Q: 4.1. The two-member pinned frame is subjected to the distributed loading shown. Member CB as a…

A: At a point in a section, stress is also known as force per unit area. Forces per unit area that act…

Q: Determine the location e of the shear center, point O, for the thin-walled member having the cross…

A: Given :

Q: 2. The 7/8 in diameter pins at A and C that support the structure are in single shear shown in…

A: Given data in question Dimensions Shear stress Diameter To find out Largest force F

Q: 2 The section of a crane hook is a rectangle 6 cm x 4 cm. The centre of curvature of the section is…

Q: Determine the reactions at the supports for the three- hinged arch shown in Fig. 3.22(a). 2.5 kt 2.5…

Q: Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T secti…

Q: Practice Problem 4.4.13: Find the magnitudes of the pin reactions at A, C, and E caused by the…

Q: Determine the total shear and unit shear at the midheight of the shearwall in Fig 3.12. For…

Q: Draw shear and moment diagram for the following frame: by Method Coherent deformations. (q1=4,0K ,…

Q: 25KN 1.5 m 1.5 m 30KN 2 m G H B 2 m 2 m De

Q: A uniform 150 kg plate is supported by three cables attached to the ring at point A. Determine the…

Q: If the load P on the beam causes the end C to be displaced by 10mm downward, determine the normal…

A: From diagram similar triangles:δLBD6=δLBD6+8δLBD=3710=4.286mm

Q: Determine the maximum shear (k) at the given structure. 10k 0.8k/ft 8k

Q: The pin-jointed truss shown in Fig. P.4.15 is attached to a vertical wall at the points A, B, Cand…

Q: Q1: The steel shaft shown in Fig. is subjected to tw concentrated torques at B and C. If the shear…

Q: Problem (6): Draw the shear and bending diagram for the following structure

A: The beam is the structural component of the structure that resists the load coming on the element.…

Q: In the shown loaded truss, P = 225 kN, calculate the following and select the correct values from…

A: Roller support there can be only one externally free reaction that is normal to the surface. It can…

Q: The structure supports a distributed load of w = 17 kN/m. The limiting stress in rod (1) is 370 MPa,…

A: Given:- The magnitude of the distributed load on DC beam = w = 17 kN/m The limiting stress in rod…

Q: 3) The member as shown in the figure is pin connected at A and rest on a smooth support at B.…

Q: 4. Determine the reactions and draw the shear and bending moment diagrams for the beam shown using…

Q: 4-m simply supported beam supports a trapezoidal pad which varies linearly from 50 kN/m at the left…

A: Determine shear force at midspan?

Q: inclined at 30° to the known directions of the In a stressed member , *0 retio u = 0.3. Determine…

Q: Question 1 Determine the maximum negative shear at E (in kN) due to dead load of 3 kN/m and the two…

Q: PROBLEM 5.63* 18 mm 2 kN/m Beam AB supports a uniformly distributed load of 2kN/m and two…

Q: Q1: The steel shaft shown in Fig. is subjected to tv concentrated torques at B and C. If the shear…

A: It is required to find angle of twist at free end which will be sum of angle of twist in both…

Q: 12KN/m 10KN/m B 5m 3m The maximum flexure stress developed he reaction at the supports - the…

Concept explainers

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.

Question

The members of the structure in Fig. 1 weight 150 lb/ft. Determine the smallest diameter pin that can be used at C if the shearing stress is limited to 4000 psi. Assume single shear

Q2/ The members of the structure in Fig. 1 weight 150 lb/ft. Determine the smallest
diameter pin that can be used at C if the shearing stress is limited to 4000 psi. Assume
single shear.
40 kN
6 ft
2 ft
C
4 ft - 3 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14
Calculate the shear stress at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
Calculate the normal stress due to flexure at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
B. Calculate the maximum shear and moment at a point 6m from the left support. Highway uniform load = 100 kN/m; highway point load = 200 kN; uniform dead load = 30 kN/m; point dead load at midspan = 50 kN.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading P(14kN)shown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (30˚)
A column with a wide-flange section has a flange width b� = 400 mmmm, height hℎ = 400 mmmm, web thickness tw�� = 13 mmmm, and flange thickness tf�� = 21 mmmm (Figure 1). Calculate the stresses at a point 75 mmmm above the neutral axis if the section supports a tensile normal force N� = 2.1 kNkN at the centroid, shear force V� = 6.8 kNkN, and bending moment M� = 3.2 kN⋅mkN⋅m as show. What is normal stress and what is shear stress
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
The Beam has a span of 9 m, fixed at both ends and carries a uniformly distributed load of w = 25 kN/m throughout its length. The beam is W 16 x 77 with the following properties: bf = 260 mm tf = 19.3 mm d = 420 mm tw = 11.6 mm Ix = 462. 02 x 106 mm4 Iy = 57.44 x 106 mm4 a. Calculate the maximum bending stress in the beam, in MPA. b. Calculate the average shearing stress in the web, in MPa.
A beam of channel section 120 mm x60 mm has uniform thickness of 15 mm. Determine the shear stress in web and flanges where shearing force is 40 kN.
The beam is supported by a pin at A and a short link BC. If P = 15 kN, determine the average shear stressdeveloped in the pins at A,B, and C. All pins are in double shear as shown, and each has a diameter of 18 mm.
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.