Members AB and BE of the truss shown consist of 25-mm-diameter steel rods (E= 200 GPa). It is given that P=72 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. | 150 kN 0.9 m E -1.2 m -1.2 m- Determine the elongation of rod BE.

Members AB and BE of the truss shown consist of 25-mm-diameter steel rods (E= 200 GPa). It is given that P=72 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. | 150 kN 0.9 m E -1.2 m -1.2 m- Determine the elongation of rod BE.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: SITUATION. For the K-truss shown, determine the following: 2 m 3 m 3 m 2 m H. 1 kN 2 m PA C EA 1 kN…

A: We will use method of joints.

Q: Take 2 KN/m in place of 1.5. Determine support reaction

A: Given data : The value of point load P=3 KN The value of uniformly distributed load q=2 KN/m…

Q: The force F in the figure is equal to 10 kN. Determine the following forces: 1. Forces at support BD…

Q: 2. The simple beam is subjected to loadings: w= 100 kN/m, F= 500 kN, M= 5000 kN-m. The lengths are:…

Q: Determine the vertical displacement of joint C of the steel truss shown inFig.a. The cross-sectional…

A: Given Data: The cross-sectional area of each member is A=400 mm2. The modulus of elasticity of the…

Q: A truss is supported by a pin at A and a roller at B as shown in the Figure Q2. Modulus of…

A: Absolute deflection of a joint. Calculate the members force due to external loading. Remove the…

Q: 6.14 Solve Prob. 6.13 assuming that the two steel plates are (a) replaced by 8 x 200-mm plates, (b)…

A: 6.14 Calculate allowable shear for given conditions

Q: Q2. Referring to Figure Q2(a) until Figure Q2(c), check the stability and determinacy of the truss.…

Q: Problem 1 (4:- O. For the given truss below, |2 k |2 k |2 k answer the questions. A = 1.5 in² and E…

Q: Question 2. Determine the vertical displacement of joint C on the truss. Each steel member has a…

A: It is given that P = 7 kN

Q: We want to construct the truss structure shown in Fig. 2. The structure has been designed to carry a…

A: Solution-

Q: Calculate for the shear force in kN at member HG of the frame shown in figure 1 using Portal Method.…

A: Assumption of portal method. Mid column carry two times the shear force as compare to the outer…

Q: 1. For the given frame below, determine the reaction of hinged supports at point A and E. Use Force…

Q: Determine the reactions at the supports F 30° 30°% 30° 30° C' E 10' 10' 10' 10' 600lb 900lb 600lb

Q: 3.For the beam loaded as shown, determine the support reactions 9 kN B C A 1.2 m 0.6 m

A: Using method of consistent deformation treating Rb as redundant.

Q: If P = 60 kN, determine the total strain energystored in the truss. Each member has a…

A: Taking moments about D, we get The forces in each member of truss can be found out by method of…

Q: . A truss is supported by a pin at A and a roller at B as shown in the Figure Q2. Modulus of…

Q: Problem 1) Trusses (a) and (b) shown below are supported by a pin at A and a roller at E and are…

A: Solution Draw the diagram tanθ=CGAG=1.52θ=tan-1(1.52)= 36.870sinθ=sin 36.870=0.6cosθ=cos36.87=0.8

Q: Determine the stress at member FE if Pu = 18.375 Kips, the area is 11 in?. Answer your problem with…

A: Given data in question Loads Dimensions of truss Span member length Area To find out Stress in…

Q: Jse Virtual Work Method to solve the orizontal displacement of joint D in mm f the truss system…

A: To find horizontal displacement at joint D

Q: Determine the horizontal displacement of joint C. Each A-36 steel member has a cross-sectional area…

A: given data: A = 400 mm2 Steel members given so, E = 200 x 103 N/mm2 The free-body diagram by a…

Q: 3. The truss in Figure is pinned to the wall at point F, and supported by a roller at point C.…

Q: 20 kN 45° All vertical members 1.5 m long All horizontal members 3.0 m long

Q: Determine the bar force of member BD (in kN) of the truss shown if P = 18 kN and Q = 90 kN. Use 3…

A: Draw the free-body diagram of the truss.

Q: For the truss shown, the force P = 1000 N. a. Determine support reactions at A and K. b. Using…

A: Solution Since you have asked multiple question, we will solve the two question for you. If you want…

Q: Question 7 H -67.5 kN 3.6 m D 112.5 kN E F 3.6 m A B 6 m +4.5 m- Use portal method to analyze the…

A: Portal method works on the assumption that includes assuming a shear force in the columns of the…

Q: orced method of analysis

Q: Solve ALL FORCES and DRAW THE SHEAR FORCE (V-D) AND BENDING MOMENT (M-D) COMPLETELY of the following…

A: Support Reactions : RA + RB = 2×12×4.5×5 = 22.5 kN ........(1)Taking moment about A,RB×9 -…

Q: 3. Determine the support reactions (a) Ay, (b) A, and (c) By for the given structure. Neglect the…

Q: Determine the resultant moment of forces about the point O? Neglect the beam thickness KKN -15 m…

Q: 2) The stvuct ure shown in the Figure is hinged at A and C. Find the horí gontal and vertical hinge…

Q: Determine the vertical displacement of joint D. The truss is made from A992 steel rods naving a…

A: consider joint A angle at A = tanθ=21.5θ= 53.13° Fy=0FADsin53.13-20=0FAD=25KNFx=0FAB+FADCos…

Q: I Review Set P = 30 kN and P, = 16 kN in (Figure 1). Part A Determine the force in member AD, and…

Q: Determine the vertical displacement of joint D. Each A-36 steel member has a cross-sectional area of…

Q: 5.0 m 5.50 m 6.0 m 7.0 m 5.0 m (1b0+SN) KN B 144 KN. E 120 KN. K _96 KN. M P R Note: SN is 27 5.0 m…

Q: Question 2. Determine the vertical displacement of joint C on the truss. Each steel member has a…

A: Determine the vertical displacement of joint C on the truss.

Q: Solve the forces in the simple space truss shown if Figure Q2 using tension coefficients. P(-4;3;0)…

Q: 1. If the shear at a point 1m from the roller support is equal to -217.65765765766kN, determine the…

A: Moment Area Method: The region under the curvature diagram between two points is adequate to the…

Q: QUESTION 2 Determine the force in member CD using method of section of the truss shown if: P= 522 Kn…

A: A truss is shown in fig. and it has been asked to determine the force in member CD using method of…

Q: If the load P on the beam below causes the end C to be displaced 10mm downward, determine the normal…

Q: 3. Find the reactions of the beam shown using: a. 3 Moment Equation b. Consistent Deformation Method…

A: Given data:

Q: Problem #4 Y KN G 30° 10 m celee B X KN 60° 60% 10 m A KN Good E 30° D 10 m Determine the force in…

Q: 1. Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End…

A: The rotating force torque is calculated because of the product of the force and also the moment of…

Q: B. Refer to the structure below: 1. Isthe structure a truss or frame? Explain. 2. Which among the…

A: Given; The force acting on the member, P = 600 kN

Q: In the truss system shown, calculate (a) the reations at support A and I, (b) The forces in each…

A: A = 4 D = 72 E = 22 H = 12

Q: Q2. A truss is supported by a pin at A and a roller at B as shown in the Figure Q2. Modulus of…

Q: ced method of analysis.

Q: Analyze the truss shown using method of joints. The following are the values of the forces: P = 18…

A: A loaded truss is given in the question and it has been asked to determine intensity and nature of…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

USING CONJUGATE BEAM METHOD Consider 150 mm x 200 mm (bxh) mm section and e = 80 GPa DETERMINE REACTION AT D Values: A = 9.4 M B = 5.5 kN/m C = 20 kN
Question 2. Determine the vertical displacement of joint C on the truss. Each steel member has a cross-sectional area of A = 300 mm2. (Esteel=200 GPa)P= 7 kN
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.41 from the support. (MPa) Properties: Beam width = 206 mmBeam height = 495 mmPu = 66.2 kNSpan of the beam = 11 mPrestressing force = 335 kNeccentricity = 105 mm
Using Virtual Work Method and Force method analysis. Determine the reactions at the supports if the support at c moves upward 4 mm. assume a is fixed and b is a fixed joint. take e = 200 gpa. i = 240(10^6) mm*.
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
Calculate for the shear force at member FE in kN of the frame shown in figure 1 using Portal Method. Enter absolute value and use 2 decimal places in your solution.
Set P1 = 70 kN, P2 = 50 kN Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member BG of the truss. b) Determine the force in member CD of the truss. c) Determine the force in member CF of the truss.
1) Determine the value of EIy at x = 3m from the left support, for the beam loaded as shown in Figure Q1.
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
key answer: T2=71.15 N tension at A T2=20.21 N tension at B
Set P1 = 70 kN, P2 = 50 kN. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member CG of the truss. b) Determine the force in member DE of the truss. c) Determine the force in member DF of the truss. d) Determine the force in member EF of the truss. e) Determine the force in member FG of the truss.
A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are used to mount the triopd at points B, D, and C. Consider the following:L1 = 2L2 = 4L3 = 5θ = 45°α = 30 Point C coordinates: (2, -2, 3) *Do not use Vectors in solving Determine the following: Force of AB = __NForce of AC = __NForce of AD = __N