Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. Thebend of the inverted tube is 1 meter above the free surface of the alcohol in the tank and 10.5meters above the ground where the alcohol is discharged.Alcohol exits the tube at atmospheric pressure. The Specific gravity of alcohol is 0.89 while g=9.81.The pressure, in kilopascal, in the bend is Blank 1P=?1m

Answered: Image /qna-images/answer/d30a7b5a-a21c-4a1b-9c43-3d7be5fe6896.jpg

Answered: meter ab re the alcc ospheric E

Engineering

Mechanical Engineering

meter ab re the alcc ospheric E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
Determine the available suction head of a pump that is taking gasoline at 204 deg. C, from a closed tank with a pressure of 585 Kpa gage. The specific gravity of gasoline is 0.78 and its vapor pressure is 620 kpa absolute. The loss in the suction pipe is 0.5m and the pump centerline is located 3.60 meters above the gasoline level. answer is 4.47 how
Water flows steadily into the Venturi tube in the following figure. In the section considered, negligible friction losses and uniform properties in the sections are assumed. The entrance area (A1) is 20 cm2, while the throat area is A2 = 10 cm2. A pressure gauge whose manometric fluid is mercury (Yhg = 136,000 N / m3) is connected between the inlet sections and the throat, as seen in the figure. The flow of water that flows through the Venturi tube is requested (γH2O = 10,000 N / m3. Answer .: ϕ = 5.8 L / s.
In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be 39.8 ft3 /s. The leakage into the tailrace was found to be 1ft3 /s. The elevation of the centerline of the shaft above, the surface of tailwater was 12.67ft. The diameter of the turbine intake was 30in and the pressure at this section was measured by a mercury U-tube. The readings in the two sides of the mercury U-Tube were 10.556 ft and 0.900 ft, the zero of the scale being at a level 3.82ft below that of the centerline of the turbine shaft. The generator output was 391.8 kW, friction and windage loss 13.8 kW, iron loss 2.0kW and armature loss of 4.4kW. The specific gravity of the mercury used was 13.57. Calculate the efficiency of the turbine.
An orifice of diameter 150 mm is fitted at the bottom of a boiler drum lenth 6 m and of diameter 2 m. The drum is horizontal and contains water up to height of 1.8 m. Find the time required to empty the boiler. Take Cd=o 0.60. a.127 seconds b.467 seconds c.175 seconds d.217 seconds
In a venturemeter used for measuring the flow of oil (S = 0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical U tube containing mercury. If the difference level between the fluids in the U-tube arms is (x +1/S.N ) in cm, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
An orifice of diameter 150 mm is fitted at the bottom of a boiler drum lenth 6 m and of diameter 2 m. The drum is horizontal and contains water up to height of 1.8 m. Find the time required to empty the boiler. Take Cd=o 0.60. Include FBD. a. 127 seconds b. 217 seconds c. 467 seconds d. 175 seconds
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
kindly help me with this problems INSTRUCTIONS: Solve the problems neatly and systematically. SUse free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 2. Water in a partially filled large tank is to be supplied to the rooftop, which is 8 m above the water level inthe tank, through a 2.5 cm internal diameter pipe by maintaining a constant air pressure of 300 kPa (gauge) inthe tank. If the head loss in the piping system is 2 m of water, determine the discharge rate of the supply ofwater to the rooftop in L/s
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.