Correct answer writing 0.012hole is specified as 300.000 mm. The mating shaft has a clearance fit with minimum clearance0.02 mm. The hole tolerance is to be 1.5 times the shaft tolerance. The maximum clearancebetween the hole and the shaft ismm.

Answered: Image /qna-images/answer/dee3a5bc-7596-4259-bf74-6376d1b3d242.jpg

Answered: mm - The mating shaft has a clearanc

Engineering

Mechanical Engineering

mm - The mating shaft has a clearanc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70 (+0.04 )/(+0.00 ) mm and Shaft = 70 (-0.04)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 40 (+0.06 )/(+0.00 ) mm and Shaft = 40 (-0.07)/(-0.015) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Problem (14): Determine tolerance value and limit dimension of the rod which a diameter is ∅127 mm, according to the g6 limit deviation (∅127f6). es=-40.64 mm, ei=-66.04 mm. Determine the basic size, tolerance and limit dimensions.
On the part shown, specify a paralellism tolerance to make the top surface parallel to datum A within a total of .002, and with both the profile and parallelism applied to the part above what is the maximum height of the top surface to datum A? Can the MMC Modifier be applied to the feature tolerance? why or why not?
Problem (2): Determine tolerance value and limit dimension of the rod which a diameter is ∅47 mm (nominal size), according to the e6 limit deviation (∅47e6). es=-25 mkm, ei=-41 mkm. Determine the basic size, tolerance and limit dimensions.
Determine tolerance value and limit dimension of the rod which a diameter is ∅50 mm, according to the g6 limit deviation (∅50H6). es=-15.24 mkm, ei=0.00 mkm. Determine the basic size, tolerance and limit dimensions.
Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7
A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire method. The diameter of the best size wire in mm is, (a) 0.866 (b) 1.000 (c) 1.154 (d) 2.000
Problem (5): Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 50 (+0.02 )/(+0.00 ) mm and Shaft = 50 (-0.05)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Problem (7): Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm, according to the H9 limit deviation (∅25H9). ES=-12.7 mkm, Eİ=+0 mkm. Determine the basic size, tolerance and limit dimensions.
Compute for the Break Mean Effective Pressure with the following information: Given: Bhp = 1000 Stroke = 5 inches Bore = 5.5 inches Rpm = 2700 Number of cylinders = 8 *Show complete solution. Thank you.
1)Find the depth of thread for M 22 X 4 X 50 internal thread. The depth of thread in mm is= Answer 2) Type of maintenance conducted to determine the actual failure by monitoring the condition of machines is known as a. Improvement maintenance b. Corrective maintenance c. Predictive maintenance d. Preventive maintenance