n engine operates with air on the cycle shown with isentropic processes 1 - 2 and 3 - 4, and constant volume processes at 2 - 3 and 4 - 1. If the compression ratio (r) is 12, the minimum pressure is 200 kPa, and the maximum pressure is 10 MPa, determine the mean effective pressure. (Note: r = V1/V2 = V4/V3)

Q: In the figure below, the losses up to section A is 5V,2/2g and the nozzle losses are 0.05V," /2g Det...

A: Given data as per question Height H =8 m D1 =150 mm D2 =50 mm calculations Water is incompressible c...

Q: A cylindrical object with a mass of m = 4.65 lbm slides into a pipe downward. The object has a diame...

A: Given: The mass of object, m = 4.65 lbm The diameter of object, d = 8.4 in The height, h = 9.9 in Th...

Q: kN, determine the magnitudes of the average normal stress in the shank, the average shear stress alo...

A:

Q: Neglecting friction and the radius of the pulley. determine the reaction at C. D 150 mm |B 120 N |A ...

A: Answer: ◆ The reaction at C is 224 N acting at 2.05°. ◆ Therefore, the correct answer is option (c).

Q: B: Find the total moment of force with respect to point (A), for the two forces in next fig. 8m 3m 5...

A:

Q: 5. What is the value in m/s^2 of the acceleration of a free falling body? O 32.2 O 9.81

A:

Q: For a 2D flow, the velocity potential function is given by = x -", find the velocity at points (2, 2...

A:

Q: Draw the Free Body Diagram only of next fig.

A:

Q: The uniform box shown in next figure, has a mass of 40 Kg. If the two forces T = 60 N and F =30 N ar...

A: For solution refer below images.

Q: Answer the following problem with complete solutions. Write legibly   Refrigerant HFC-134a is ideal...

A:

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal Dia...

A:

Q: Owhat is The ad vantageoFusing matrix méThod in Para x ral oPt i^cs? ob hain The sxstem matrix Por a...

A:

Q: 1) Replace the 800-lb couple system at (a

A: Given Force To find Couple system at O Couple system at P

Q: Calculate the pressure at a point 40 cm below the surface of the oil in a vessel. Express the answer...

A:

Q: 5. What is the value in m/s^2 of the acceleration of a free falling body?

A: Given:Free falling acceleration induced in the body when it is falling freely downward withoutany ex...

Q: a) In an open vessel, a certain volume V of water is perfectly agitated by means of an impeller 20 c...

A: Given: Diameter of the impeller→D=20 Cm speed of the impeller→N=150 RPM=150/60=2.5 revolution per se...

Q: For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respecti...

A: From the figure given in question, Maximum stress in the cycle = σmax = 250 MPa Minimum stress in th...

Q: Q. A shaft rotating N rpm under a torque T transmits a power of answer choices T*Pi*N/30 Newton mete...

A: Given, Shaft RPM = N Torque transmitted by shaft = T   From the shaft RPM, its angular velocity (ω) ...

Q: Truss fill in the blank

A: Given data : Number of joint=J J=4 Number of member=m m=4 Number of support reaction=R R=2+2=4  

Q: Reynolds number, based on the pipe diameter

A: Given; Two pipes of uniform section but different diameters carry water at the same flow rate.Water ...

Q: Question 1 A light propagates inside a single step index fiber with a speed of 2.0013 × 108?/? and h...

A: Given Datav=2.0013×108m/sα=5.4370°λ=1.48μm-1.60μm

Q: Draw the Free Body Diagram only of next fig.

A: To find : free body diagram of given figure

Q: A fluid occupies 1.5 cubic meters. If it has a mass of 2,500 kg, calculate the specific gravity.

A: Answer: The specific gravity of the fluid is 1.67.  

Q: 27 Find the transfer function Y(s) tem shown in Figure E2.27.

A: To find  Transfer function

Q: 6. An ammonia refrigeration system operates in a simple saturation vapour compression cyde to produc...

A:

Q: Part A Member CB has a square cross section of 30 mm on each side. (Eigure.1) Determine the largest ...

A:

Q: 3.13 A uniform flow with a velocity of 3 m/s is superimposed on the plane source of strength 20 m³/s...

A:

Q: What is the Gravitational Potential at position 1 for mB? Answer: Check What is the Potential Energy...

A:

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made ...

A: Given data Initial Diameter = d = 1.95 inFinal Diameter = D =2.05 in

Q: The uniform box shown in next figure, has a mass of 40 Kg. If the two forces T = 60 N and F =30 N ar...

A:

Q: A solid circular bronze [G = 6,500 ksi] shaft, 4.6 ft long and 1.575 in. in diameter, carries a torq...

A:

Q: Provide the complete formula and solution and free body diagram. The density of ice is 917 kg/m^3, a...

A:

Q: In an expected value calcufation, the of a situation are enumerated Answer:

A: The probable outcomes of an event are listed in order to calculate the expected value calculation of...

Q: 1. Given a four-bar linkage with the link lengths Li = d = 100 mm, L2 = a = 40 mm, L3 = b = 120 mm, ...

A: Given data L1=R1=d=100mm L2=R2=a=40mm L3=R=b=120mm L4=R4=c=80mm theta 2 = 100 degrees. 1. Scale used...

Q: An industrial adiabatic heat exchanger utilizes cold-water stream to cool down the waste-hot air flo...

A:

Q: A heat pump consumes around 3 kW of power, minimum. If the outside temperature reached -2°C and the ...

A:

Q: Q1: The two vectors A and B in Fig. below have equal magnitudes of 10 m. Find the Result (R) magnitu...

A:

Q: Question 3 2 lb-mass of a mixture (Cp - 3.85 J/g K) must be heated 30 degrees C in 12 seconds. The h...

A: Given, Mass of the mixture = m = 2 lb = 0.907 kg Specific heat of the mixture = Cp = 3.85 J/g-K = 3....

Q: Explain why fasteners, such as bolt-and-nut, used in machines operating at high temperature must be ...

A: If the material of the bolt and the joint are different, large differences in temperature due to rap...

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 10 kN, determi...

A:

Q: Why is there a laser beam shooting out of the front of this telescope (in the inset picture)?

A: Given Telescope To find Laser beam shooting out of telescope  

Q: The axial assembly consists of a solid 1.01-in-diameter aluminum alloy [E- 8900 ksi, v - 0.33, a = 1...

A:

Q: An air stream with a Mach number of (3.04) a pressure of (302 kPa) and a temperature of (502 K) ente...

A:

Q: Consider the sprinkler which rotates at A when water flows out at B. At this instant, the sprinkler ...

A:

Q: bite angle in degree will be

A: Given; Thickness of a metallic sheet is reduced from an initial value to a final value in one single...

Q: 1. The mean effective pressure of an engine running at 300 rpm is 500 kPa. What is the indicatedpowe...

A: Givenpart aP=500kPaN=300rpmd=250mmL=450mmpart bh1=1500kJ/kgV1=150m/sh2=1200kJ/kg

Q: What is the hardest metal? What is it's Vicker's Hardness score?

A:

Q: QUESTION The weights of two children sitting at ends A and B of a seesaw are 40 Ib and 65 lb, respec...

A:

Q: 1. A vertical plate is submerged in water. Find an integral expression that can be evaluated to dete...

A:

Q: 1. Steam with specific volume of 0.09596 m/kg undergoes a constant pressure process at 1.80 Mpa unti...

A: