Name the methods used for refining of following metals :(i) Nickel(ii) Titanium
Q: Discuss the different uses of grain processing by-products
A: Grain processing by-products are the products that are obtained after the grains are processed to…
Q: Show that for homogeneous nucleation during solid state transformation the critical radius r* is…
A: Nucleation is defined as the localised development of an unique thermodynamic phase in a gas,…
Q: Your current carburizing process produces a case depth of 4 mm in 7 hours. If you want to increase…
A:
Q: 3) The dihedral wetting angle between solid- liquid interface with lowest solidification cracking…
A: The angle for the solidification is 600
Q: in a tabular format compare microstructure,for different cast irons and steel
A: Types Nature Form Comments Ferrite Soft and ductile In the form of flakes Cementite(Fe3C)…
Q: The notch sensitivity factor, q, for gray cast iron is very low. Offer an explanation in terms of…
A:
Q: Define nucleation phase
A: given: Define nucleation phase.
Q: The obtained microstructure of annealing process is Bainite O Coarse pearlite O Martensite O Fine…
A:
Q: Suppose you are asked to manufacture a critical component based on a nickel-based super-alloy. The…
A: GIVEN: Manufacture a critical component based on nickel based super alloy
Q: Translate the given information in your words, figures given below. Time-temperature cooling curve…
A: Cooling Curve: It is a curve that represents the phase of material from gas to liquid or liquid to…
Q: Calculate the dihedtal angle for a ratio of the interfacial energies Yss/ Ysl equal to 1.732 at a…
A: Given data:
Q: Comparison of treatment processes (annealing, normalizing, hardening and tempering) according to…
A: Heat treatment processes: Those processes that alter the mechanical properties of steel by varying…
Q: I need the answer as soon as possible
A: Notch sensitivity factor of grey cast iron can be defined as the ratio of increases in the actual…
Q: Describe and discuss, using sketches, the difference between substitution and interstitial solid…
A: An alloy is a combination of two or more metals or a metal and a non-metal which then forms a new…
Q: Explain the concept of zone refining and also explain the refining technique for germanium ingot.
A: Given Germanium ingot To find Zone refining Germanium ingot refining
Q: Differentiate between the following transformations Pearlite, (b) Bainitic (c) Martensitic, based on…
A: Steel is quenched, usually with water or oil, to produce pearlite. The main distinction between it…
Q: A lattice point at a corner of one unit cell is shared by O four adjacent unit cells two adjacent…
A: 1) There are total 8 cubic unit cell that are placed in symmetricity so that every lattice point at…
Q: The temperature at which Nitinol remembers its high temperature form/shape can be adjusted by slight…
A:
Q: 4) The features of grain structure having highest solidification cracking susceptibility is Coarse…
A: The highest solidification cracking susceptibility is COARSE GAINS AND LOW ANGLE GRAIN BOUNDARIES
Q: A cube shaped casting solidifies in 5 minutes. The solidification time in minutes for a cube of the…
A: Given, Let Volume of the lighter cube be V1 & Volume of the heavier cube be V2 Since both are…
Q: 1. What is Age Hardening and how does it differ from Quench Hardening?
A: Age Hardening
Q: Compare the carbonization and nitrification of steel
A: To compare : Carbonization of steel (Carburizing) Nitrification of steel (Nitriding) Carburising…
Q: A mole of supercooled liquid of silver, undergoing isothermal irreversible solidification at 700 °C,…
A:
Q: One of the most common production techniques for metallic implants is lost-wax casting. Discuss the…
A: Lost wax casting, also known as investment casting is a casting process that makes use of wax…
Q: Which ingot has greater mechanical resistance? Why? Explain in detail what occurred during…
A: Given image : the image is showing two different ingot which shows the grain struture where one is…
Q: The needle form of mullite offering substantial increasing in structural strength and heat…
A: Mullite is present in the form of needles in porcelain. It is produced during various melting and…
Q: 2) The region showing planar growth during solidification near the fusion zone boundary will exhibit…
A:
Q: A form of boron nitride (BN) known as hexagonal boron nitride is used as a solid lubricant. Explain…
A: Boron Nitride (BN) is formed by the combination of Boron and Nitrogen. It is a synthetic material…
Q: 1. What is the driving force in this separation technique? 2. What purpose does acetic acid serve in…
A: 1.By definition, driving forces exploit variations in chemical/physical properties between 2…
Q: wWucsuons © 1. Differentiate between the following transformations Pearlite, (b) Bainitic (c)…
A: Steel is quenched, usually with water or oil, to produce pearlite. The main distinction between it…
Q: Describe and discuss, using sketches, the difference between substitution and interstitial solid…
A: The properties of substitution and interstitial solid solution.
Q: Normalizing: This treatment will not cause any phase changes, but recovery & recrystallization may…
A: Normalization is the heat treatment process in order to increase the ductility of the material.
Q: Lead-Tin (Pb-Sn) alloys are used in soldering applications. Draw phase diagram and Distinguish…
A: The phase daigram of the Lead and Tin (Pb-Sn) is shown below.
Q: Question a Clood weting of the solid by the liquid is a fundameotal tequirement for hiquid phase…
A: Given data:
Q: Compare carbonization and nitrification
A: The comparison between carbonization and nitrification is given as under.
Q: Question:- Explain the following terms and state when/where they are used. Homology modeling…
A: Please find the solution below
Q: Based on fundamental understanding of thermodynamics, briefly explain why points defects are stable…
A: Point defects are those defects that come under the formation of a vacancy that leads to 'missing…
Q: Describe a method by which “ODS” alloys are produced and explain why it is not possible to cast…
A: Oxide dispersion strengthened (ODS) alloys, usually produced by a dispersion of nano-sized rare…
Q: List out of gas -solid mass transfer operations with suitable example and explain its industrial…
A: Dry ice, naphthalene, arsenic are examples of gas - solid mass transfer. Liquid liquid mass…
Q: Describe how to apply the lever rule to calculate relative amounts of phases in a phase diagram of…
A: Lever rule: It is a concept which is used to determine the mass fraction or mole fraction of each…
Q: compare among annealing, normalizing, hardening and tempering
A:
Q: Outline the advanced casting process that would be most suitable for making total knee replacement…
A: The advanced casting process for knee replacement is investment casting.
Q: make a comparison between annealing, normalizing hardening, and tempering
A: The main difference between annealing and normalizing is that annealing allows the material to…
Q: explain the significance of equivalance ratio. How does the product gas content change with…
A: Air - Fuel ratio- For a combustion process the air fuel ratio is the mass ratio of the air to fuel…
Q: lication requires ultimate tensile strength and yield strength of a steel at 110 ksi and 91 ksi,…
A: 4.1. Can SAE 1040 steel be selected for this application? Ans :Yes, SAE 1040 steel can be selected…
Name the methods used for refining of following metals :
(i) Nickel
(ii) Titanium
Step by step
Solved in 5 steps with 3 images
- What is a eutectic composition?Compare carbonization and nitrificationQ. What are the advantages and disadvantages of metal furnaces compared with graphite furnaces? Q. What are the advantages and disadvantages of filaments compared with graphite furnaces? Q. How has the original design of the West rod been moified to minimize these disadvantages?
- Explain how a form of boron nitride known as hexagonal boron nitride is used as a solid lubricant. Compare this form to two forms of carbon: diamond and graphite.Suppose you are asked to manufacture a critical component based on a nickel-based super-alloy. The component must not contain any porosity and it must be chemically homogeneous. What manufacturing process would you use for this application? Why?The needle form of mullite offering substantial increasing in structural strength and heat resistance? (Provided that the answer is scientific brief)
- Good wetting of the solid by the liquid is a fundamental requirement for liquid phase sintering. Answer the following questions. Calculate the dihedtal angle for a ratio of the interfacial energies Yss/ Ysl equal to 1.732 at a particular sintering temperature. How would you describe the microstructure based on your calculation ?Explain annealing process?Compare the carbonization and nitrification of steel