Question a Cood wetting of the solid bby the liquid is a fundameotal tequirement for iquidphase sintering Considering the lgure given below, ower the following questionsliquidsolidsolidgrain boundarydihedral angleCalculate the dihedral angle for a ratio of the interfacial energies Y Yst equal to1.732at a particular sintering temperature. How would you describe the microstructure based on yourcalculation?Answer:

Question a Clood weting of the solid by the liquid is a fundameotal tequirement for hiquid phase sintering Considering the figure given below, aower the following questions quit solid solid grain boundary V dihedral angle You Calculate the dihedral angle for a ratio of the interfacial energies Y Yst equal to 1.732 at a particular sintering temperature. How would you describe the microstructure based on your calculation? Answer:

Question a Clood weting of the solid by the liquid is a fundameotal tequirement for hiquid phase sintering Considering the figure given below, aower the following questions quit solid solid grain boundary V dihedral angle You Calculate the dihedral angle for a ratio of the interfacial energies Y Yst equal to 1.732 at a particular sintering temperature. How would you describe the microstructure based on your calculation? Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a CO molecule, the constant E is approximately 0.00024 eV. (This number is measured using microwave spectroscopy, that is, by measuring the microwave frequencies needed to excite the molecules into higher rotational states.) Calculate the rotational partition function for a CO molecule at room temperature (300 K), first using the exact formula and then using the approximate formula
Good wetting of the solid by the liquid is a fundamental requirement for liquid phase sintering. Answer the following questions. Calculate the dihedtal angle for a ratio of the interfacial energies Yss/ Ysl equal to 1.732 at a particular sintering temperature. How would you describe the microstructure based on your calculation ?
Assume the total heat of vaporization (per gram) of water can be used to supply the energy needed to tear 1 gram of water molecules apart from each other. What is the ratio of energy needed per molecule to kT where 1.38x10^-23 J/K?
Explain what material properties link to nozzle and bed temperature. Plot a graph of the process windows of nozzle temperature and print bed temperature representing the 3D FDM printing temperature range for a material X. The Melting Point of X is the 2nd, 3rd and 4th digit of your student ID and the Tg of X is the 5th and 6th digit of your student ID. If your second digit is 0, use from the 3rd digit to the 7th digit. Eg: Student ID 216456783, Mp = 164°C & Tg = 56°C.
Consider a dispersion strengthened alloy with average interparticle spacing of L. If Nv is he number ofparticle per unit volume, d is the particle dimeter, and Vp is the volume fraction of particle, then whatwill be the expression for interparticle spacing in term of the particle diameter and volume fraction?
In precipitation hardening, after being quenched into solution, overcooling is done and then either artificial aging is done at 180-250°C or natural aging is done at room temperature, both of which occur through diffusion, where temperature and time parameters are dominant. While 180°C and 250°C provide sufficient temperature for diffusion, is it not interesting that diffusion occurs at room temperature? This is because of the thermal energy of atoms causing them to move, which may facilitate diffusion at room temperature.
Please kindly help. I will give a like. Thank you! a. Describe the S-curve model of diffusion on how does ‘rate of adoption’ change over time? At which-point is the rate of diffusion the fastest? b. S-curve model of diffusion: (true/false) and reasoning - k = 0, the rate of diffusion is instantaneous? - fixed k ≥ 0, the carrying capacity is determined only by the ratio of a and b? - fixed k ≥ 0, the rate of diffusion is determined only by the ratio of a and b? c. The diffusion of hybrid corn in the 1940s, who or which region seems to have adopted the hybrids more quickly and why?
The recommended sintering time for a pressed part is 20 min. The sintering chamber of the flow-through furnace is 4.0 m long. The number of parts that can be placed on 1 m of conveyor belt length is 15 pc. Determine the (a) speed of the conveyor, (b) processing rate of the furnace, and (c) quantity of parts being sintered at one time.
Give a physical reason why the curve in the graph would not reach the vertical (Elost) axis even if the scientists had taken data over a broader range of temperatures. As S increases, Elost approaches a maximum value labeled Emax on the graph above. Write an equation for Emax in terms of M, D, and physical constants, as appropriate. Justify your answer. One of the scientists, in trying to represent the relationship between the oil stiffness and the mechanical energy lost, writes down the equation 2 Elost = CS2, where C is a constant with appropriate units. Another scientist points out that this equation cannot be correct. Give two reasons why the equation cannot be correct.
Derive expression for the lumped analysis in terms of Fourier and Biot numbers.
Thermal Diffusivity Estimate the thermal diffusivity of butter at 20°C.
With reference to the attached example. Apply dimensinal analysis to show that all values/units used are homogeneous.