ne. The dimensions of the various links are as follows : 200 mm; AB = 100 mm; OC= 400 mm; and CR= 150 mm. iving crank A B makes 120° with the vertical and rotates at 60 r.p.m. in the clockwise direction. 1. velocity of ram R, and 2. angular velocity of the slotted link OC. [Ans. 0.8 m/s ; 1.83 rad/s] Be R B'(on OC) 60 C(on BD) 120
Q: given below, in the arm slide mechanism, the actuating limb angular position is (theta)θ12 = 600 and…
A:
Q: grams, and determine the length s of length. angular displacement B1, in deg ngular displacement B2,…
A: L= 16681 β=68 degree = β 1 + β2 L1= 0.298 (a) → L= L1+ L2 L 2 =L-L1= 1661-0.298 = 1660.702…
Q: The number of degrees of reedom is what determines he number of generalized coordinates. (True or…
A: It is true.
Q: M2 Delermike X for thesgshem abore
A:
Q: ✓ Figure shows a wheel rotating about O₂. Two points A and B located along the radius of wheel have…
A:
Q: which represents direction of @point 2. वि 23/ ? , Pu lincar acceleration
A: Linear acceleration is in the direction of D1.
Q: Offset OA= 10 cs AB 20 cm BDC TDC For the slider-crank mechanism shown, the offset is 9 cm (Note:…
A:
Q: In a rotating body, if it rotates at 2270 revolutions per minute.What would be the angular velocity…
A:
Q: Cylindrical coordinates 1 1 a²T 1 ôT r ôr Or a ôt
A: Heat conduction: It is defined as the transfer of internal heat energy by collision of microscopic…
Q: kwise direction. Find the locities by creating a velo olidWorks. Submit the file in the below…
A:
Q: The piston and cylinder of an internal combustion engine are shown in the following figure. If @ =…
A: Given: The length of connecting rod, L = 200 mm The crank radius, r = 50 mm The position of crank =…
Q: Unit system: MMGS (millimeter, gram, second) Decimal places: 2 All holes through all unless shown…
A:
Q: 2.velocity of sliding of CE in the trunnion, and 3. angular velocity of CE.
A:
Q: The equatte to Denve the eend Cul ct aimplitude f tatres rese
A:
Q: (Eigure 1) Part A Determine the x and y components of the velocity of the block B at the instant…
A:
Q: One morning, Connie walks from her house to go to a store that is 500 ft, S 40o W from her house.…
A:
Q: s (m) 600 360 (s) 30 40
A:
Q: The nozzle in the figure leaves cooling water from point A on the grinding disc with v0 speed and ao…
A:
Q: Evaluate the integral dy dx using polar coordinate
A:
Q: For a given non-symmetric area and origin, when plotting Mohr's Circle, a reference point doesn't…
A: Identify the reference point on the mohr circle.
Q: 13 64 026 for the given sketch above. sketch the ORTHOGRAPHIC VIEW USING CATIA V5
A:
Q: 3 A wheel of radius 0.3 m travels with constant speed 30 m/s around a track of radius 30 m. What is…
A: as per guideline i have to solve only first part of the question
Q: Expalin the construction of velocity and Acceleration digrams
A: Velocity : Velocity is rate of change of displacement, so velocity diagram the diagram which shows…
Q: In a rotating body, if it rotates at 2355 revolutions per minute.What would be the angular velocity…
A:
Q: it reaches and aft nt= 0, a car locat- a constant speed
A: given:initial velocity u=0m/sfinal velocity v=40kph=40×518=11.11m/sacceleration a=2m/s2car located…
Q: Find the value of the following: A. The piston speed of an air compressor is 150m/min and has a…
A: Answer (A): Given data: v=150 m/minQ=0.8 m3/s Need to determine the diameter(in) of compressor…
Q: 3. Fxz²i + (1 - 3xy)j + yzk, A. xyi + 2yzj - 3yk B. zi + 2xzj - 3yk C. zi + 2zj3xk D. xi + 2yzj -…
A:
Q: An angular velocity of 50 rad/s expressed is approximately .. (rpm =revolutions per minute) O 100r…
A: Calculated rpm ( revolution per minute).
Q: * =For the given data shown. EAy 7 in in HE A3 A1 Neutral Axis N.A) 12 in A2 Reterence Line Aren No.…
A:
Q: Refer to the figure below and solve for the linear velocities (ft/s) of all the points on the Jse…
A:
Q: In a rotating body, if it rotates at 2045 revolutions per minute.What would be the angular velocity…
A: Angular velocity Angular velocity is the rotational velocity of a body. It is equal to the angular…
Q: w = wo sin (7x) Wo A L if wo-(acute angle between the hands of a clock at 7:30 A.M.) Ib/ft and…
A:
Q: n, use the m angian undet-
A:
Q: O cm, DC = 30 cm, AD = 20 cr kes an angle of 180° with AD velocity of 3 rad/sec in counte ngular…
A:
Q: The decimal equivalent of 5EA716 i , А. 24064 В. 24081 C. 24231 24640 Е. 24641 D.
A:
Q: Airplane propeller The length of the largest airplane propeller ever used was 22 feet 7.5 inches.…
A: As given that propeller turned by 4 engines with N= 545 rpm ;So the angular velocity of the…
Q: Q1: Draw the orthographic Projections of given object. 15 20 R20 O REDMI NOTE 9 PRO MAX O AI QUAD…
A: Orthographic Projection is a 2 dimensional projection of a 3 Dimensional object.
Q: use AutoCAD to make a three-view drawing, complete with dimensions, of the part.
A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…
Q: he magnitude of the acceleration of
A: a=1.923m/s^2 UP
Q: Match List-I (NC Code) with List-II (Definition) and select the correct answer using the codes given…
A:
Q: Copyright © McGraw-Hill Education. Permission required for reproduction or display. -3.6 m A 2400 N…
A: When an amount of push or the pull applied on a body, it has the tendecy to change its state from…
Q: dulum to complete two oscillatio
A: Given Data→ topic-Simple pendulum Maximum angular accelerationMaximum angular velocity=θmax,,θmax,=π
Q: A/0 =? r,=40 cm 0,=10.t²+30 (deg) Calculate the velocity of point A in X-Y coordinate system when t…
A:
Q: 6. Give all the location dimensions between the datum target areas, A1 and A2 . Z = Page 1 of 3 7.…
A: The location dimension is an indication of the location of an object in a view. Observe the given…
Q: (a) Figure Q1(a) shows a gear system. Find (i) The relationship between the number of the gear teeth…
A: Solution: The answer to the given question is given below:
Q: P1-2) Model the following object. Note that the dimensions are given in millimeters.
A:
Q: Assignment 2 E B to A SkN 5kN SKN Calcu late Porcej h each men ber of tmuss, Use method of jo ch ts.
A:
Step by step
Solved in 2 steps with 2 images
- An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 200 kg at the crank pin, and the reciprocating masses per cylinder to 300 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the value of variation in tractive effort at 300 rpm. Select one: A. ±58476 N B. ±69780 N C. ±79654 N D. ±12475 NFor the mechanisms below, determine the number of instantaneous centers of rotation.Q#03 : In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+25 rpm clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD? (Subject : mechanics of machines)
- The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.Q#03 :In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+(23) r.p.m clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD?A band and block brake having 10 blocks, each of which subtends an angle of 14o at center, is applied todrum of effective diameter of 1 m. The brake drum and winding drum of crane mounted on the sameshaft weighs 20 kN and have combined radius of gyration of 300 mm. The two ends of the band areattached to the pin on opposite side of the fulcrum. If an effort of 300 N is applied at distance of 800mm from the fulcrum, find (i) Braking torque, (ii) the angular retardation of the brake, (iii) the timetaken by the system to come to rest from the rated speed of 400 rpm. Take coefficient of frictionbetween the drum and the block as 0.25.
- Three cylinders A:B:C rolling in external contact has a speed ratio of 4:2:1. If the diameter of cylinder A is 10 cm, find the center distance between cylinder A and C.The arms of a Porter governor are equal in length and pivot on the axis of rotation. The mass of each ball is 10 kg and the mass of the central load is 25 kg. The ball rotates at radius 210 mm when the governor is at its lowest setting and 260 mm when it is at its maximum setting. At maximum speed, the vertical distance from the center of the sleeve to the pivot was 500 mm. For another case, it can be seen that the height of the governor will reduce to half values when the ball masses are replaced by three-time larger from the first case. The friction force for both cases is 10 N. Find arms length LDetermine the range of speed in first casewhat will be the final range of speedAs a result of extracting the speed range values in both cases, what did you conclude?In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+1r.p.m clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD?
- A shaft is rotating at a uniform angular speed. Four masses M1, M2, and M3 and M4 of magnitudes 300kg, 450kg, 360kg, 390kg respectively are attached rigidly to the shaft. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mmand 300mm respectively. The angle made by these masses with horizontal are 0°.45°, 120°and 255°respectively. Find-(i) the magnitude of balancing mass (ii) the position of balancing mass if its radius of rotation is 200mm.A shaft carries four masses, B, C, and D of magnitude 200 kg, 300 kg, 400 kg, and 200 kg respectively and revolving at radii 80 mm, 70 mm, 60 mm, and 80 mm in planes measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks measured anticlockwise are A to B 45º, B to C 70º, and C to D 120º. the balancing masses are to be placed in planes X and Y. The distance between the planes A and X is 100 mm, between X and Y is 400 mm and between Y and D is 200 mm. If the balancing masses revolve at a radius of 100 mm, find their magnitude and angular positions.A 2.5 ft diameter flywheel of a gas engine has a pulley 10 in. in diameter bolted to it (both turning together). The flywheel turns at a speed of 150 rpm. Find a. the angular speed of the pulley in radians per second b. the linear speed in feet per minute of a point on the surface of the flywheel c. the linear speed in feet per minute of a belt running on the pulley, assuming no slipping between the belt and pulley surface.