Newtons and x is the displacement in meters. Assume displacement data is known The force vs. displacement data for a linear spring is given below. F is the force in more accurately. Displacement, x (m) Force, F (N) 10 15 20 200 400 100 Jf the F vs x data is regressed to F a+ kx, what is the value of k by minimizing the sum of the square of the residuals?

Newtons and x is the displacement in meters. Assume displacement data is known The force vs. displacement data for a linear spring is given below. F is the force in more accurately. Displacement, x (m) Force, F (N) 10 15 20 200 400 100 Jf the F vs x data is regressed to F a+ kx, what is the value of k by minimizing the sum of the square of the residuals?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).
5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
Using Newton’s laws, we could show that for some pendulums, the period T is related to the length l and free-fall acceleration g by T=2pi square root of (l/g) , or T2 = (4pi2/g) * l Does one of your graphs support this relationship? Explain. (Hint: Can the term in parentheses be treated as a constant of proportionality?)
A 45 grams (0.045 kg) golf ball of diameter equal to 43 mm fell into a 2m deep lake. Neglect inertia at the moment of impact. Assume viscosity of 1.12x10-3 Ns/m2 , water density of 1,000 kg/m3 and Cd=0.5. Sphere volume equals 4π r³ /3. 1. How long will it take from the moment it hits the surface until it gets to the bottom? 2. If one estimates the Cd with Cd=24/Re formula, the settling velocity would be unrealistically large. Why?
When using the method of repeated variables in a problem, it is determined that one of the independent Πs is given by the product between the independent variable lift force FL [N], and the repeated variables density ρ [kg/m3], velocity V [m/s], and area A [m2]. Remembering that Πs are given by the product of the primary dimensions raised to the zero power, of the type m0L0t0 T0, determine this independent Π. (the form is in the side picture)
I just need help simplifying these equations (1 and 2). Qo,Kic, and CL are all their own variables (not 2 multiplied ie. Q*o, k*i*c and not C*L)
A bullet is to be tested in the laboratory to determine the drag force on it. Dependent parameter the drag force D (Newton) depends on the velocity of the bullet V(m/s), the length of the bullet L(m), sound velocity c(m/s), density of fluid ρ (kg/m3) and dynamic viscosity µ(kg/ms). Solve the problem by making the necessary assumptions and drawing the schematic figure. I-Determine the nondimensional p parameters using repeating variables ii-a bullet with a speed of 96,2 m/s in air may be modelled in a water tunnel with a test section velocity of 262 cm/s. Determine the length of the model, if the length of the bullet is 56,2 mm. The air and water temperature is 20 oC degree at 1 atm. iii- if the drag force on the model is measured to be 2,62 N, then determine the expected drag force on the bullet. Comment on dynamic similarity equivalence?
Consider the following equation. All three of the terms in parentheses are dimensionless groups. Because kC is difficult to determine directly, the other variables are measured and kC is calculated from the given equation. What is the estimated value of kC? What are the units of kC? Show your work. The following values were measured: D = 8.0 mm, DAB = 0.475 cm2/s, μ = 1.12 x 10–3 N-s/m2, ρ = 1.00 x 10–3 g/cm3, v = 15.0 m/s. Note: Given Equation attached below
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V,pressure difference P, fluid density  and viscosity .a) (15P) Determine dimensionless  groups.b) (20P) A test is to be performed for a large pump that delivers 1.5 m3/s of water from 40 cmdiameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impelleris to be used. What flow rate should be used and what would be the pressure rise in model pump
Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is:
Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the wind speed V, the air density ρ, the acceleration of gravity g, the length of the banner L and the “area density” of the flag material ρA (with dimensions of ML-2 ). In order to estimate the flutter frequency of a large banner with L = 40 ft in a V = 30 ft/s wind, a small banner with L = 4 ft is to be tested in a wind tunnel. (a) What is the area density of the small banner when the large banner has area density of 0.006 slugs/ft2? (b) What should the wind tunnel velocity be to test the small model? (c) It has been shown that the small banner flutters at 6 s-1 when the same area density and wind tunnel velocity are used in parts (a) and (b). In this case, what is the fluttering frequency of the large banner?