NOTE This is a multi-part question, Once an answer is submitted, you will be unable to return to this part Consider the area shown in the figure, where r= 75 in. Semicirele 45 in. Problem 09.045.0 - Find Polar Moments about origin Determine the poler moment of inertie of the area with respect to point O (You must provide an answer before moving on to the next part) The polar moment of inertie of the area with respect to point Ois

NOTE This is a multi-part question, Once an answer is submitted, you will be unable to return to this part Consider the area shown in the figure, where r= 75 in. Semicirele 45 in. Problem 09.045.0 - Find Polar Moments about origin Determine the poler moment of inertie of the area with respect to point O (You must provide an answer before moving on to the next part) The polar moment of inertie of the area with respect to point Ois

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.78P: The L806010-mm structural angle has the following cross-sectional properties:...

See similar textbooks

Similar questions

Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
Determine Ix for the triangular region shown.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Determine the dimension b of the square cutout so that Ixy=0 for the region shown.
Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y of the plane region shown.
The flanged bolt coupling is fabricated by drilling 10 evenly spaced 0.5-in. diameter bolt holes in a steel plate. The radii of the plate and bolt circle are 5 in. and 4 in., respectively. Determine the percent reduction in the polar moment of the area about point O due to the drilling operation.
Use integration to verify the formula given in Table 9.2 for Ixy of a half parabolic complement.
Compute Ix and Iy for the region shown.
The L806010-mm structural angle has the following cross-sectional properties: Ix=0.808106mm4,Iy=0.388106mm4, and I2=0.213106mm4, where I2 is a centroidal principal moment of inertia. Assuming that Ixy is negative, compute (a) I1 (the other centroidal principal moment of inertia); and (b) the principal directions at the centroid.
Find the first moment of area, why don’t you include the middle portion in the calculation?
A simply supported beam has a symmetrical rectangular cross-section. If thesecond moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. (show all work)