NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air enters a nozzle steadily at 50 psia, 140°F, and 150 ft/s and leaves at 14.7 psia and 900 ft/s. The heat loss from the nozzle is estimated to be 6.5 Btu/lbm of air flowing. The inlet area of the nozzle is 0.09 ft2. The enthalpy of air at the inlet is h₁ 143.47 Btu/lbm.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air enters a nozzle steadily at 50 psia, 140°F, and 150 ft/s and leaves at 14.7 psia and 900 ft/s. The heat loss from the nozzle is estimated to be 6.5 Btu/lbm of air flowing. The inlet area of the nozzle is 0.09 ft2. The enthalpy of air at the inlet is h₁ 143.47 Btu/lbm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refrigerant-134a at 700 kPa and 120°C enters an adiabatic nozzle steadily with a velocity of 20 m/s and leaves at 400 kPa and 30°C. Determine (a) the exit velocity and (b) the ratio of the inlet to exit area A1/A2.
Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s.
Question 2 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 5 MPa, 600°C, and 90 m/s, and the exit conditions are 50 kPa, 90 percent quality, and 55 m/s. The mass flow rate of the steam is 14 kg/s. Determine: 2.1 The turbine inlet area, and 2.2 The power output in MW.
The turbines in steam power plants operate essentially under adiabatic conditions. A plant engineer suggests ending this practice. She proposes to run cooling water through the outer surface of the casing to cool the steam as it flows through the turbine. This way, she reasons, the entropy of the steam will decrease, the performance of the turbine will improve, and as a result the work output of the turbine will increase. How would you evaluate this proposal?
Hot combustion gases enter the nozzle of a turbojet engine at 230 kPa, 627°C, and 60 m/s and exit at 70 kPa and 450°C. Assuming the nozzle to be adiabatic and the surroundings to be at 20°C, determine the exit velocity.
Air is expanded isentropically from 100 psia and 500°F to 20 psia in a closed system. Determine its final temperature
Steam flows steadily through an adiabatic turbine. The inlet conditionsof the steam are 10 MPa, 450°C, and 80 m/s, and the exit conditions are 10 kPa, and 50 m/s.The mass flow rate of the steam is 12 kg/s. The power output of the turbine is 10.2 MW.Determine(a) the temperature of the water as it leaves the turbine,(b) the quality x of the water as it leaves the turbine,(c) the inlet and outlet cross-sectional area.
Air enters an adiabatic nozzle at 45 psia and 940°F with low velocity and exits at 650 ft/s. If the isentropic efficiency of the nozzle is 85 percent, determine the exit temperature and pressure of the air.
Saturated vapor enters the turbine at 8.0 MPa and exits 0.008 MPa. The turbine has an isentropic efficiency of 82.26%. Velocity and elevation changes are insignificant. Determine the electrical power it can produce in kW if the mass of steam is 25.2 kg/s, and the mechanical and electrical efficiencies are 75.56% and 93.31%. FINAL ANSWER MUST BE IN 3 DECIMAL POINTS.
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
Steam enters a turbine with an enthalpy of 3300 KJ/kg and leaves with an enthalpy of 2400 kJ/kg. The power output of the steam turbine is 6 MW
A steady-flow thermodynamic system receives 100 lb/min of fluid at 30 psia and 200 Fahrenheit and discharges it from a point 80 ft above the entrance section at 150 psia and 600 Fahrenheit. The fluid enters with velocity of 1200 fpm and leaves with a velocity of 200 fpm. During this process, there are supplied 25,000 Btu/hr of heat from an external source and the increase in enthalpy is 2 Btu/lb. Determine the work done in horsepower.