Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the glass stays approximately rigid. Determine the average shear strain in the nylon due to the load P when the assembly deforms as indicated. 2 mm 3 mm 5 mm 3 mm 5 mm 3 mm 0.197 rad 0.297 rad O 0.397 rad O 0.125 rad O none of the above

Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the glass stays approximately rigid. Determine the average shear strain in the nylon due to the load P when the assembly deforms as indicated. 2 mm 3 mm 5 mm 3 mm 5 mm 3 mm 0.197 rad 0.297 rad O 0.397 rad O 0.125 rad O none of the above

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 51PQ

See similar textbooks

Similar questions

Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the ends of the walk are unable to move. Take Youngs modulus for concrete to be 7.00 109 N/m2 and the compressive strength to be 2.00 109 N/m2. (a) What is the stress in the cement on a hot day of 50.0C? (b) Does the concrete fracture?
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
A spring 1.50 m long with force constant 475 N/m is hung from the ceiling of an elevator, and a block of mass 10.0 kg is attached to the bottom of the spring. (a) By how much is the spring stretched when the block is slowly lowered to its equilibrium point? (b) If the elevator subsequently accelerates upward at 2.00 m/s2, what is the position of the block, taking the equilibrium position found in part (a) as y = 0 and upwards as the positive y-direction. (c) If the elevator cable snaps during the acceleration, describe the subsequent motion of the block relative to the freely falling elevator. What is the amplitude of its motion?