O Figure 3 shows a beam at static condition is supported by a pin and cables at point A, B and C respectively. If the weight of the cylinder, W is 80 N and 15 kN/m triangular distributed load acts along member AB, determine the tension of the cables and reaction of the supports. IСОЗ, РОЗ, СЗ] E 15 N/m B D 5 m 5 m 3 m W

O Figure 3 shows a beam at static condition is supported by a pin and cables at point A, B and C respectively. If the weight of the cylinder, W is 80 N and 15 kN/m triangular distributed load acts along member AB, determine the tension of the cables and reaction of the supports. IСОЗ, РОЗ, СЗ] E 15 N/m B D 5 m 5 m 3 m W

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

The frame has dimensions H1 = 4 m , H2 = 3 m , and L1 = 6 m , and supports two lateral loads P1 = 10 kN and P2 = 12 kN . The area of column AE is 40 cm2 and the area of column BF is 80 cm2 . Gy = 13.3 kN Ax = 11.0 kN a) What is the horizontal reaction from the ground on the base of the column at B? Let a positive reaction be pointing to the left. Bx = ?
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?
The steel rod is fixed to the side at ‘A’, and before it is loaded, there is a gap of 0.15-mm between the side at ‘D’ and the other end of the rod at ‘C’ as shown in the figure below. Determine the support reactions at ‘A’ and ‘D’ if the rod is subjected to an axial force, ? = 200-??. Take ??? = 200-???.
Uniform slender bar ABC of mass m = 5 kg and length L = 3m is pinned at A and supportedby a cable attached at B. The cable runs over a frictionless pulley at E, but the small pulley at Dhas seized and will not rotate; the coefficient of static friction between the cable and the seizedpulley at D is 0.2. The pulley at E supports a cylinder of mass M. Find the mass M required toinitiate counterclockwise (CCW) rotation of bar ABC. α = 30o and θ = 25o.
the mobile crane (weight =48 kN) moves across the brige of length, l =14m. the front wheels of the mobile carry the three-quarter of its weight while the rear wheels carry a quarter of its weight. iif the distance between front and rear wheel is b = 0.7m. Determine themaximum value of bending moment as it moves across
The frame is used to support a live load of 1.575 kPa. Thickness of concrete slab is 124.903mm. Weight of concrete is 23.293 kN/m^3. Weight of beam BG,AH,CF,DE is 4.526 kN/m and that of is 5.413 kN/m L=5.918m Width"B" = 1.582m Compute the reaction at point A (kN) at member AD Answer: 71.118 Need solution
GIVEN: L1 = 4.5 m W1 = 10 kN/m L2 = 1.2 m W2 = 12 kN/m L3 = 0.5 m L4 = 12 m L5 = 1.5 m A. What is the maximum shear in Beam D-E-B? B. What is the maximum moment in Beam A-B-C?
The frame shown in Figure is hinged at E and roller supported at A. Determine the horizontal and vertical components of the hinge forces at B. a.) Bh= 24 KN & Bv=56 KN b.) Bh=48 KN & Bv= 81 KN c.) Bh=24 KN & Bv= 81 KN d.) None of the Above e.) Bh= 48 KN & Bv=56 KN
The 115-mm-diameter steel shaft is subjected to the torques shown. T1 = 14 kN-m, T2 = 2 kN-m, T3 = 2 kN-m. Determine the angle of twist (degrees) of the end B. Use L1 = 0.75 m., L2 = 0.53 m., L3 = 0.69 m. Shear modulus = 71 GPa.
From the frame shown, solve for the moment reaction at fixed support. (kN m) a. 490 CCW b. 530 CCW c. 620 CW d. 585 CCW
A propped beam has a span of 7.2 meters is simply supported at C. It carries a concentrated load of 60 kN, 3 meters from C. EI = 3000 kN.m2. reaction at C, in kN angle of rotation at C deflection at B, in mm
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.