IG =1.35 kg m coefficients of friction between the spool and the ground are 0.30 and 0.27, respectively. A cable wound around the hub of the spool is pulled with 400 mm- 150 the constant horizontal force P= 200 N. a) Draw the free body (FBD) and the kinetic (KD) diagrams. b) Find the acceleration of the center of the

IG =1.35 kg m coefficients of friction between the spool and the ground are 0.30 and 0.27, respectively. A cable wound around the hub of the spool is pulled with 400 mm- 150 the constant horizontal force P= 200 N. a) Draw the free body (FBD) and the kinetic (KD) diagrams. b) Find the acceleration of the center of the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A load W is to be lifted using the crane which is hinged at B as shown in the figure. The value of x1 is 10m, x2 is 8m and h is 18m. Neglecting the weight of the crane. Determine the following. 1. Force at cable AC. 2. Resultant reaction at B. 3. Largest load that can be lifted if the maximum force of cable AC is 50kN.
The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 199 N and if a = 3m, determine the magnitude of the reaction (N) at A along the y-axis. Round off only on the final answer expressed in 3 decimal places .
The system is released from rest with the cable taut. The mass of blocks A and B are 54 kg and 25 kg, respectively. For the friction coefficients ?s = 0.25 and ?s = 0.2, calculate the tension in the cable in Newton. Neglect the small mass and friction of the pulleys. Use g = 9.81 m/s2
The 80kg cylinder A is supported by a flexible cable C at 20° and a smooth plane. Determine all forces in Newton acting on Cylinder A.
Calculate the components of reaction at the support A and also the tension in the cable BC. F = 80 N, M = 40 N.m
1. The transmission tower OA is being hoisted into position by the cables AB and AC. The resultant of the cable tensions P and Q, along with the 2400-lb weight of the tower, is a force R acting at point O. Determine P, Q, and R.\ 2.
Consider the three-dimensional structure shown in the figure, fixed to the ground at point O, and restrained by cables AB and CD. The tension TT in the restraining cable CD is 2.8 kN. Calculate the magnitude of the vector moment (in kNm) produced by the force exerted by the cable CD on point C, about the point O (assume use of the right-hand rule). Take aa = 4.7 metres, and bb = 3.8 metres.
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
A pulley-and-cable assembly supports block W and requires a downward force at P for equilibrium. Knowing that the tension of cable FG is 61.2 N, calculate the mass of the block and the magnitude of the downward force P.
1. The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. Draw the FBD
Two blocks A and B have a mass of 10 kg and 100 kg, respectively. Block B is released from rest. Give the tension in the cable, the equation with corrected sign, acceleration of block A.
ENGINEERING MECHANICS (No lng explanation needed. Write the complet solutions and legibly. Rate will be given) Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively The allowable shearing stress is 1 GPa with F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E. Where: Radius of the gear at B, rB = 100mm Radius of the gear at C, rC = 150mm