Objective 7 Level 1 4 m- A The jib crane is supported by a pin at C and rod AB. If the load has a mass of 1000 Kg with its center of mass located at G, determine the horizontal 3.2 m and vertical components of 0.2 m B reaction at the pin C and the force developed in rod AB on the crane when x = 5 m. Forces must be in Newtons. D

Objective 7 Level 1 4 m- A The jib crane is supported by a pin at C and rod AB. If the load has a mass of 1000 Kg with its center of mass located at G, determine the horizontal 3.2 m and vertical components of 0.2 m B reaction at the pin C and the force developed in rod AB on the crane when x = 5 m. Forces must be in Newtons. D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.90P: The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of...

See similar textbooks

Similar questions

Don't copy from other websites solution. The wall crane supports a load of 660lb. The jib ABC has a weight of 152lb and member BD has a weight of 38lb. Each member is uniform and has a center of gtravity at its center. A)Determine the horizontal component of reaction at the pin A. B)Determine the vertical component of reaction at the pin A. C)Determine the horizontal component of reaction at the pin D. D)Determine the vertical component of reaction at the pin D. E)What is the force in the cable at the winch W?
The torsional spring at B is undeformed when bars OB and BD are both in the vertical position and overlap. If a force F is required to position the bars at a steady orientation θ = 64°, determine the torsional spring stiffness kT. The slot at C is smooth, and the weight of the bars is negligible. In this configuration, the pin at C is positioned at the midpoint of the slotted bar.
The rigid block of mass M is supported by the three symetrically placed rods. The ends of the rods where level before the block was attached. Determine the largest allowable value of M if the properties of the rods are as listed: -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Referring to Prob. 10.43 and using the value found for the force exerted by the hydraulic cylinder CD , determine the change in the length of CD required to raise the 10-kN load by 15 mm.Reference to Problem 10.43:
A 120-lb weight is attached to the cable that is wrapped around the 50-lb homogeneous drum. Theshaft attached to the drum is supported by a thrust bearing at A and a slider bearing at B. The drum iskept in equilibrium by the vertical force P acting on the handle of the crank. Determine P and thereactions at A and B. Neglect the weights of the crank and the shaft. Provide a free-body-diagram.
Assuming the pulley system below is weightless and frictionless pulley, determine reaction force at the ceiling when 375 N load is lifted and held in static equilibrium. Give your answer in Newtons (N) to 2 decimal places.
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) Calculate the moment reaction at A. (ANSWER: 28.499) Calculate the total reaction at A. (ANSWER: 22.192) Calculate the vertical reaction at E. (ANSWER: 25.223)
The spring is connected to a rope that passes over the cylindrical surface and is attached to corner A of the rocker. The spring has a stiffness k and is undeformed when =0. When the weight W is suspended from A, the equilibrium position of the rocker is =30. Determine if this equilibrium position is stable. Neglect the weight of the rocker.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
Draw the FBDs for the entire structure and the member BDE. Count the total number of unknowns and the total number of independent equilibrium equations. Note that the cable that supports the 1200-lb weight runs over a smooth peg at D.
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.