Mechanics of deformable bodies: PROBLEM: The beam shown is made by gluing together four pieces 300mm x 12mm wooden planks as shown.8 kN12mm5 kN/m300mm12mm8m- 2m -6m300mm(a)Solve for the moment of inertia of the cross section formed.(b)Determine the maximum moment in the beam(c)Determine the maximum bending stress in the beam due to the given loads.

Answered: Image /qna-images/answer/1fa5b6dc-4c19-4b84-a546-de335e4617e3.jpg

OBLEM: The beam shown is made by gluing together four pieces 300mm x 12mm wooden planks 8 kN 5 kN/m 30 B| 8m 2m 6m - 300mm (a) Solve for the moment of inertia of the cross section formed. (b) Determine the maximum moment in the beam (c) Determine the maximum bending stress in the beam due to the given load:

OBLEM: The beam shown is made by gluing together four pieces 300mm x 12mm wooden planks 8 kN 5 kN/m 30 B| 8m 2m 6m - 300mm (a) Solve for the moment of inertia of the cross section formed. (b) Determine the maximum moment in the beam (c) Determine the maximum bending stress in the beam due to the given load:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The elevation of the end of the steel beam supported by a concrete floor is adjusted by means of the steel wedges E and F . The base plate CD has been welded to the lower flange of the beam, and the end reaction of the beam is known to be 18 kips. The coefficient of static friction is 0.30 between two steel surfaces and 0.60 between steel and concrete. If the horizontal motion of tin beam is prevented by the force Q . determine (a) the force P required to raise the beam, (b) the corresponding force Q.
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
The uniform 50-lb beam is supported by the rope that is attached to the end of the beam, wraps over the rough peg, and is then connected to the 100-lb block. If the coefficient of static friction between the beam and the block, and between the rope and the peg, is μs = 0.4, determine the maximum distance that the block can be placed from A and still remain in equilibrium. Assume the block will not tip.
a) Compute R1 in Newton. b) Compute R2 in Newton. c) Compute the value of EIy at the midspan of the beam in kN-m^3.
consider the 20m beam shown • what is the location of the absolute maximum moment from the center of the beam? answer in m •what is the maximum moment when the middle load is positioned at the center of the beam? answer in kN-m
Determine from the beam and the loads shown:a) Reactions on supportsb) Shear force diagramc) Bending moment diagramd) The neutral axise) The moment of inertiaf) The first moment of areag) The maximum normal efforth) The maximum shear stressi) Deflection at the midpoint of the beam. Beam section in the picture (plg)
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
determine the slope at the left support A (in degrees). the beam is loaded with a moment load M=18kN-m at its midspan. EI is constant and equal to 38,058 kN-m^2. use length of beam L=9m
Replace the distributed loading by an equivalent resultant force and couple moment acting at point A.
A 5.98-m simply supported beam supports a trapezoidal distributed load. The intensity of the load varies linearly from 0N/m at supports A to 60.72N/m at support B.-Calculate the location of zero shear.(in meters)-Calculate the maximum moment experienced by the beam-Explain the relationship between the shear and flxural stresses experienced by the beam
Determine the effective depth of the beam in mm.0 Determine the critical shear Vu in kN.0 Determine the load to be carried by the stirrups Vs in kN.0